DataSheet.es    


PDF KV-27FS120 Data sheet ( Hoja de datos )

Número de pieza KV-27FS120
Descripción FD Trinitron WEGA
Fabricantes Sony 
Logotipo Sony Logotipo



Hay una vista previa y un enlace de descarga de KV-27FS120 (archivo pdf) en la parte inferior de esta página.


Total 56 Páginas

No Preview Available ! KV-27FS120 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
Connecting Additional Equipment
4-101-456-21(1)
U.comOperating Instructions
www.DataSheet4© 2004 by Sony Corporation
KV-27FS120
www.DataSheet4U.com

1 page




KV-27FS120 pdf
Connecting Additional Equipment
Never block the slots and openings
by placing the set on a bed, sofa, rug
or other similar surface.
Never place the set in a confined
space, such as a bookcase or built-in
cabinet, unless proper ventilation is
provided.
Do not place the set near or over a
radiator or heat register, or where it is
exposed to direct sunlight.
Power-Cord Protection
Do not allow anything to rest on or roll over the
power cord, and do not place the set where the
power cord is subject to wear or abuse.
Antennas
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions
below. An outdoor antenna system should not be located in
the vicinity of overhead power lines or other electric light or
power circuits, or where it can come in contact with such
power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA
SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP
FROM CONTACTING SUCH POWER LINES OR
CIRCUITS AS CONTACT WITH THEM IS ALMOST
INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in USA and
Section 54 of the Canadian Electrical Code in Canada
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the NEC
Antenna Grounding According to the National Electrical
Code, ANSI/NFPA 70.
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ELECTRIC
SERVICE
EQUIPMENT
NEC - NATIONAL ELECTRIC CODE
Lightning
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
For added protection for this television receiver during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the
receiver due to lightning and power-line surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
When the power cord or plug
is damaged or frayed.
If liquid has been spilled
into the set or objects have
fallen into the product.
If the set has been exposed to
rain or water.
If the set has been subject to
excessive shock by being
dropped, or the cabinet has
been damaged.
If the set does not operate
normally when following the operating
instructions. Adjust only those controls
that are specified in the operating
instructions. Improper adjustment of
other controls may result in damage and
will often require extensive work by a
qualified technician to restore the set to normal operation.
When the set exhibits a distinct change in
performance — this indicates a need for service.
Servicing
Do not attempt to service the set yourself
since opening the cabinet may expose you
to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Replacement Parts
When replacement parts are required, be
sure the service technician certifies in
writing that he has used replacement
parts specified by the manufacturer that
have the same characteristics as the
original parts. Unauthorized
substitutions may result in fire, electric
shock, or other hazards.
Safety Check
Upon completion of any service or repairs to
the set, ask the service technician to perform
routine safety checks (as specified by the
manufacturer) to determine that the set is in
safe operating condition, and to so certify.
When the set reaches the end of its useful life,
improper disposal could result in a picture
tube implosion. Ask a qualified service
technician to dispose of the set.

5 Page





KV-27FS120 arduino
Using the Remote Control
Remote Control Description
Button
Description
1 MUTING
Press to turn off the sound. Press again or press
to restore sound.
2 SYSTEM OFF
Press to turn off the equipment programmed into
A K the remote control. See “Programming the Remote
Control” on page 5. This button does not work with
B L DVD/VCR combo units, and may not work with
older Sony equipment.
C
M 3 TV/VCR/DVD
Press to change the VHF/UHF output of the VCR
(or DVD/VCR combination unit). If you have a
N non-Sony VCR or DVD, you will need to program
D
E
the remote control to recognize your VCR or DVD.
O For details, see “Programming the Remote Control”
on page 5.
P 4 PICTURE MODE Press repeatedly to step through the available video
Q picture modes: Vivid, Standard, Movie and Pro.
Also available in the Video menu. See “Using the
Video Menu” on page 28 for details.
F
5 SLEEP
Press repeatedly until the TV displays the time in
G
minutes (15, 30, 45, 60, or 90) that you want the TV
R to remain on before shutting off automatically.
S
Cancel by pressing until Sleep Off appears. While
the Sleep feature is set, press once to view the
H T remaining time.
6 JUMP
Press to jump back and forth between two channels.
The TV alternates between the current channel and
I
U
the last channel that you selected. JUMP will not
work if any FUNCTION Mode (VCR/DVD, SAT/
CABLE, TV) is activated.
J
7 TV/SAT
Press to switch between the TV and SAT (satellite)
inputs when in SAT FUNCTION mode.
Press for a direct selection of Effect settings
(Simulated, SRS, Off) when the remote is in TV
FUNCTION mode. See “Using the Audio Menu” on
page 29 for details.
8 RESET
Press to return to factory settings while in an
on-screen menu.
9 VOL (volume)
Press (+) or (-) to adjust the volume.
3

11 Page







PáginasTotal 56 Páginas
PDF Descargar[ Datasheet KV-27FS120.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
KV-27FS120(KV-27/32/36FS120) TVSony
Sony
KV-27FS120FD Trinitron WEGASony
Sony

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar