|
|
PDF ICL7667 Data sheet ( Hoja de datos )
| Número de pieza | ICL7667 | |
| Descripción | Dual Power MOSFET Driver | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ICL7667 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Data Sheet
ICL7667
April 1999 File Number 2853.3
Dual Power MOSFET Driver
The ICL7667 is a dual monolithic high-speed driver
designed to convert TTL level signals into high current
outputs at voltages up to 15V. Its high speed and current
output enable it to drive large capacitive loads with high slew
rates and low propagation delays. With an output voltage
swing only millivolts less than the supply voltage and a
maximum supply voltage of 15V, the ICL7667 is well suited
for driving power MOSFETs in high frequency switched-
mode power converters. The ICL7667’s high current outputs
minimize power losses in the power MOSFETs by rapidly
charging and discharging the gate capacitance. The
ICL7667’s inputs are TTL compatible and can be directly
driven by common pulse-width modulation control ICs.
Ordering Information
PART
TEMP. RANGE
NUMBER
(oC) PACKAGE
PKG. NO.
ICL7667CBA
0 to 70 8 Ld SOIC (N) M8.15
ICL7667CPA
0 to 70 8 Ld PDIP
E8.3
ICL7667CJA
0 to 70 8 Ld CERDIP F8.3A
ICL7667CTV
0 to 70 8 Pin Metal Can T8.C
ICL7667MTV
(Note 1)
-55 to 125 8 Pin Metal Can T8.C
ICL7667MJA
(Note 1)
-55 to 125 8 Ld CERDIP F8.3A
NOTE:
1. Add /883B to Part Number for 883B Processing
Functional Diagram
VCC
≈ 2mA
OUT
IN
Features
• Fast Rise and Fall Times
- 30ns with 1000pF Load
• Wide Supply Voltage Range
- VCC = 4.5V to 15V
• Low Power Consumption
- 4mW with Inputs Low
- 20mW with Inputs High
• TTL/CMOS Input Compatible Power Driver
- ROUT = 7Ω Typ
• Direct Interface with Common PWM Control ICs
• Pin Equivalent to DS0026/DS0056; TSC426
Applications
• Switching Power Supplies
• DC/DC Converters
• Motor Controllers
Pinouts
ICL7667 (CAN)
TOP VIEW
OUT A 1
V+
8
7 OUT B
N/C 2
6 N/C
IN A 3
5 IN B
4
V-
ICL7667 (PDIP, SOIC, CERDIP)
TOP VIEW
N/C 1
IN A 2
V- 3
IN B 4
8 N/C
7 OUT A
6 V+
5 OUT B
3-73
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1 page  
ICL7667
peak current capability of the ICL7667 enables it to drive a
1000pF load with a rise time of only 40ns. Because the
output stage impedance is very low, up to 300mA will flow
through the series N-Channel and P-channel output devices
(from VCC to ground) during output transitions. This crossover
current is responsible for a significant portion of the internal
power dissipation of the ICL7667 at high frequencies. It can be
minimized by keeping the rise and fall times of the input to the
ICL7667 below 1µs.
Application Notes
Although the ICL7667 is simply a dual level-shifting inverter,
there are several areas to which careful attention must be
paid.
Grounding
Since the input and the high current output current paths
both include the ground pin, it is very important to minimize
and common impedance in the ground return. Since the
ICL7667 is an inverter, any common impedance will
generate negative feedback, and will degrade the delay, rise
and fall times. Use a ground plane if possible, or use
separate ground returns for the input and output circuits. To
minimize any common inductance in the ground return,
separate the input and output circuit ground returns as close
to the ICL7667 as is possible.
Bypassing
The rapid charging and discharging of the load capacitance
requires very high current spikes from the power supplies. A
parallel combination of capacitors that has a low impedance
over a wide frequency range should be used. A 4.7µF
tantalum capacitor in parallel with a low inductance 0.1µF
capacitor is usually sufficient bypassing.
Output Damping
Ringing is a common problem in any circuit with very fast
rise or fall times. Such ringing will be aggravated by long
inductive lines with capacitive loads. Techniques to reduce
ringing include:
1. Reduce inductance by making printed circuit board traces
as short as possible.
2. Reduce inductance by using a ground plane or by closely
coupling the output lines to their return paths.
3. Use a 10Ω to 30Ω resistor in series with the output of the
ICL7667. Although this reduces ringing, it will also slightly
increase the rise and fall times.
4. Use good bypassing techniques to prevent supply voltage
ringing.
Power Dissipation
The power dissipation of the ICL7667 has three main
components:
5. Input inverter current loss
6. Output stage crossover current loss
7. Output stage I2R power loss
The sum of the above must stay within the specified limits for
reliable operation.
As noted above, the input inverter current is input voltage
dependent, with an ICC of 0.1mA maximum with a logic 0
input and 6mA maximum with a logic 1 input.
The output stage crowbar current is the current that flows
through the series N-Channel and P-channel devices that
form the output. This current, about 300mA, occurs only
during output transitions. Caution: The inputs should never
be allowed to remain between VIL and VIH since this could
leave the output stage in a high current mode, rapidly
leading to destruction of the device. If only one of the drivers
is being used, be sure to tie the unused input to a ground.
NEVER leave an input floating. The average supply current
drawn by the output stage is frequency dependent, as can
be seen in ICC vs Frequency graph in the Typical
Characteristics Graphs.
The output stage I2R power dissipation is nothing more than
the product of the output current times the voltage drop
across the output device. In addition to the current drawn by
any resistive load, there will be an output current due to the
charging and discharging of the load capacitance. In most
high frequency circuits the current used to charge and
discharge capacitance dominates, and the power dissipation
is approximately
PAC = CVCC2f
where C = Load Capacitance, f = Frequency
In cases where the load is a power MOSFET and the gate
drive requirement are described in terms of gate charge, the
ICL7667 power dissipation will be
PAC = QGVCCf
where QG = Charge required to switch the gate, in
Coulombs, f = Frequency.
Power MOS Driver Circuits
Power MOS Driver Requirements
Because it has a very high peak current output, the ICL7667
the at driving the gate of power MOS devices. The high
current output is important since it minimizes the time the
power MOS device is in the linear region. Figure 9 is a
typical curve of charge vs gate voltage for a power MOSFET.
The flat region is caused by the Miller capacitance, where
the drain-to-gate capacitance is multiplied by the voltage
gain of the FET. This increase in capacitance occurs while
the power MOSFET is in the linear region and is dissipating
significant amounts of power. The very high current output of
the ICL7667 is able to rapidly overcome this high
capacitance and quickly turns the MOSFET fully on or off.
3-77
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet ICL7667.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ICL7660 | CMOS Voltage Converters |  Intersil |
| ICL7660 | Switched-Capacitor Voltage Converters |  Maxim Integrated |
| ICL7660A | CMOS Voltage Converters | Intersil |
| ICL7660S | Super Voltage Converter | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |