DataSheet.es    


PDF HCPL-0452 Data sheet ( Hoja de datos )

Número de pieza HCPL-0452
Descripción (HCPL-xxxx) Single Channel / High Speed Optocouplers
Fabricantes Hewlett-Packard 
Logotipo Hewlett-Packard Logotipo



Hay una vista previa y un enlace de descarga de HCPL-0452 (archivo pdf) en la parte inferior de esta página.


Total 16 Páginas

No Preview Available ! HCPL-0452 Hoja de datos, Descripción, Manual

Single Channel, High Speed
Optocouplers
Technical Data
Features
Applications
sheet4u.com6N135/6
taHCNW135/6
HCNW4502/3
aHCPL-2502
.dHCPL-0452/3
HCPL-0500/1
wwwHCPL-4502/3
Description
• 15 kV/µs Minimum Common
Mode Transient Immunity at
VCM = 1500 V (4503/0453)
• High Speed: 1 Mb/s
• TTL Compatible
• Available in 8-Pin DIP, SO-8,
Widebody Packages
• Open Collector Output
• Guaranteed Performance
from Temperature: 0°C
to 70°C
• Safety Approval
UL Recognized – 2500 V rms
for 1 minute (5000 V rms for
1 minute for HCNW and
Option 020 devices) per
UL1577
CSA Approved
VDE 0884 Approved
–VIORM = 630 V peak for
HCPL-4503#060
–VIORM = 1414 V peak for
HCNW devices
• Dual Channel Version
Available (253X/4534/053X/
0534)
• MIL-STD-1772 Version
Available (55XX/65XX/4N55)
• High Voltage Insulation
• Video Signal Isolation
• Power Transistor Isolation
in Motor Drives
• Line Receivers
• Feedback Element in
Switched Mode Power
Supplies
• High Speed Logic Ground
Isolation – TTL/TTL, TTL/
CMOS, TTL/LSTTL
• Replaces Pulse Transformers
• Replaces Slow
Phototransistor Isolators
• Analog Signal Ground
Isolation
These diode-transistor optocoup-
lers use an insulating layer
between a LED and an integrated
photodetector to provide elec-
trical insulation between input
and output. Separate connections
for the photodiode bias and
output-transistor collector
increase the speed up to a
hundred times that of a conven-
tional phototransistor coupler by
reducing the base-collector
capacitance.
Functional Diagram
NC 1
ANODE 2
CATHODE 3
NC 4
8 VCC
*
7 VB
6 VO
5 GND
TRUTH TABLE
(POSITIVE LOGIC)
LED
VO
ON
OFF
LOW
HIGH
* NOTE: FOR 4502/3, 0452/3,
PIN 7 IS NOT CONNECTED.
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.

1 page




HCPL-0452 pdf
5
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6,
HCNW4502/3)
11.15 ± 0.15
(0.442 ± 0.006)
PAD LOCATION (FOR REFERENCE ONLY)
87
65
9.00 ± 0.15
(0.354 ± 0.006)
1234
(06.2.1452)TYP.
12.30 ± 0.30
(0.484 ± 0.012)
1.55
(0.061)
MAX.
(04.1.0508)MAX.
1.3
(0.051)
0.9
(0.035)
12.30 ± 0.30
(0.484 ± 0.012)
11.00 MAX.
(0.433)
1.78 ± 0.15
(0.070 ± 0.006)
2.54
(0.100)
BSC
0.75 ± 0.25
(0.030 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
1.00 ± 0.15
(0.039 ± 0.006)
0.254
+ 0.076
- 0.0051
(0.010+-
0.003)
0.002)
7° NOM.
Solder Reflow Temperature Profile (HCPL-0500/1, HCPL-0452/3, and Gull Wing
Surface Mount Option Parts)
260
240
220
200
180
160
140
120
100
80
60
40
20
0
0
T = 115°C, 0.3°C/SEC
T = 100°C, 1.5°C/SEC
1 23 4 5 6 7 8
TIME – MINUTES
T = 145°C, 1°C/SEC
9 10 11 12
Note: Use of Non-Chlorine Activated Fluxes is Recommended.

5 Page





HCPL-0452 arduino
11
Package Characteristics
Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified.
Parameter
Input-Output
Momentary
Withstand
Voltage**
Sym.
VISO
Device
8-Pin DIP
SO-8
Widebody
Min. Typ.* Max. Units Test Conditions Fig. Note
2500
V rms RH < 50%,
6, 14
5000
t = 1 min.,
TA = 25°C
6, 15
Input-Output
Resistance
Input-Output
Capacitance
8-Pin DIP 5000
(Option 020)
II-O 8-Pin DIP
1
RI-O 8-Pin DIP
SO-8
1012
Widebody 1012 1013
1011
CI-O 8-Pin DIP
SO-8
0.6
Widebody
0.5 0.6
µA 45% RH, t = 5 s,
VI-O = 3 kVdc,
TA = 25°C
VI-O = 500 Vdc
TA = 25°C
TA = 100°C
pF f = 1 MHz
6, 12,
15
6, 16
6
6
*All typicals at TA = 25°C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Related Characteristics Table (if
applicable), your equipment level safety specification or HP Application Note 1074 entitled “Optocoupler Input-Output Endurance
Voltage,” publication number 5963-2203E.
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).
2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF,
times 100.
6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the
common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode
transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse
signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V).
8. The 1.9 kload represents 1 TTL unit load of 1.6 mA and the 5.6 kpull-up resistor.
9. The 4.1 kload represents 1 LSTTL unit load of 0.36 mA and 6.1 kpull-up resistor.
10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Agilent guarantees a minimum CTR of 19%.
12. See Option 020 data sheet for more information.
13. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended.
14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 3000 V rms for 1 second
(leakage detection current limit, II-O 5 µA). This test is performed before the 100% Production test shown in the VDE 0884
Insulation Related Characteristics Table if applicable.
15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 6000 V rms for 1 second
(leakage detection current limit, II-O 5 µA). This test is performed before the 100% Production test shown in the VDE 0884
Insulation Related Characteristics Table if applicable.
16. This rating is equally validated by an equivalent ac proof test.

11 Page







PáginasTotal 16 Páginas
PDF Descargar[ Datasheet HCPL-0452.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
HCPL-0452SINGLE CHANNEL HIGH SPEED TRANSISTOR OPTOCOUPLERSFairchild Semiconductor
Fairchild Semiconductor
HCPL-0452Single Channel/ High Speed OptocouplersAgilent(Hewlett-Packard)
Agilent(Hewlett-Packard)
HCPL-0452(HCPL-xxxx) Single Channel / High Speed OptocouplersHewlett-Packard
Hewlett-Packard
HCPL-0452High Speed OptocouplersAvago
Avago

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar