DataSheet.es    


PDF DMC-50218N-B Data sheet ( Hoja de datos )

Número de pieza DMC-50218N-B
Descripción LCD Module Specification
Fabricantes OPTREX CORPORATION 
Logotipo OPTREX CORPORATION Logotipo



Hay una vista previa y un enlace de descarga de DMC-50218N-B (archivo pdf) en la parte inferior de esta página.


Total 15 Páginas

No Preview Available ! DMC-50218N-B Hoja de datos, Descripción, Manual

LCD Module Specification
Type No. DMC-50218N-B
First Edition
Apr 21, 1999
Final Revision
*******
Approved by
Checked by
Checked by
Prepared by
Production Div.
Quality Assurance Div.
Design Engineering Div.
Production Div.
Table of Contents
1. General Specifications .............................................................................2
2. Electrical Specifications...........................................................................3
3. Optical Specifications ..............................................................................5
4. I/O Terminal.............................................................................................7
5. Test............................................................................................................9
6. Appearance Standards............................................................................10
7. Code System of Production Lot ..........................................................13
8. Type Number..........................................................................................13
9. Applying Precautions .............................................................................13
10. Precautions Relating Product Handling................................................14
11. Warranty..................................................................................................15
Revision History
Rev. Date
Page
Comment
DMC-50218N-B (AB) No.99-0093
OPTREX CORPORATION
OPTREX
Page 1/15

1 page




DMC-50218N-B pdf
3.Optical Specifications
3.1.LCD Driving Voltage
Parameter
Symbol
Conditions
Min. Typ. Max. Units
Recommended
Ta= 0
- - 5.4 V
LCD Driving Voltage
VCC-VEE
Ta=25
4.4 4.7 5.0
V
Note 1
Ta=50
4.2 - - V
Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of
minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and
response time are not guaranteed over the entire range.
3.2.Optical Characteristics
Ta=25, 1/16 Duty, 1/4.5 Bias, VD=4.7V (Note 4), θ= 0 , φ=-゚
Parameter
Symbol
Conditions
Min. Typ. Max. Units
Contrast Ratio
Note 1
CR
θ= 0 , φ=-゚
5
Viewing Angle
Shown in 3.3
Response Rise Note 2
TON
- - 130 200 ms
Time Decay Note 3
TOFF
- - 180 280 ms
Note 1 : Contrast ratio is definded as follows.
CR = LOFF / LON
LON : Luminance of the ON segments
LOFF : Luminance of the OFF segments
Note 2 : The time that the luminance level reaches 90% of the saturation level from 0% when ON
signal is applied.
Note 3 : The time that the luminance level reaches 10% of the saturation level from 100% when OFF
signal is applied.
Note 4 : Definition of Driving Voltage VD
Assuming that the typical driving waveforms shown below are applied to the LCD Panel at
1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage VD is definded
as follows.
VD = (Vth1+Vth2) / 2
Vth1 : The voltage VO-P that should provide 50% of the saturation level in the luminance at
the segment which the ON signal is applied to.
Vth2 : The voltage VO-P that should provide 50% of the saturation level in the luminance at
the segment which the OFF signal is applied to.
VO-P
1 / ( fF×A )
ON SIGNAL
DMC-50218N-B (AB) No.99-0093
1 / fF
( B-2 )×VO-P / B
OFF SIGNAL
OPTREX CORPORATION
OPTREX
Page 5/15

5 Page





DMC-50218N-B arduino
6.3.Standards
No. Parameter
Criteria
1 Black and
(1) Round Shape
White Spots,
Zone
Acceptable Number
Foreign Substances
Dimension (mm)
ABC
D 0.1
*
*
*
0.1 D 0.2
5
5
*
0.2 D 0.3
0
1
*
0.3 D
00*
D = ( Long + Short ) / 2 * : Disregard
(2) Line Shape
Zone
Acceptable Number
X(mm) Y(mm)
ABC
2.0L
1.0L
1.0L
0.02W
0.03W
0.04W
0.05W
0.05W
***
33*
12*
02*
In the same way (1)
X : Length Y : Width * : Disregard
Total defects shall not exceed 5.
2 Air Bubbles
(between glass
Zone
Acceptable Number
& polarizer)
Dimension (mm)
ABC
D 0.15
*
*
*
0.15D 0.3 2 3 *
0.3 D 0.5 1 2 *
0.5 D 1.0 0 1 *
* : Disregard
Total defects shall not exceed 3.
DMC-50218N-B (AB) No.99-0093
OPTREX CORPORATION
OPTREX
Page 11/15

11 Page







PáginasTotal 15 Páginas
PDF Descargar[ Datasheet DMC-50218N-B.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
DMC-50218N-BLCD Module SpecificationOPTREX CORPORATION
OPTREX CORPORATION

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar