DataSheet.es    


PDF LM2462 Data sheet ( Hoja de datos )

Número de pieza LM2462
Descripción Monolithic Triple 3 ns CRT Driver
Fabricantes National Semiconductor 
Logotipo National Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de LM2462 (archivo pdf) en la parte inferior de esta página.


Total 11 Páginas

No Preview Available ! LM2462 Hoja de datos, Descripción, Manual

February 2002
LM2462
Monolithic Triple 3 ns CRT Driver
General Description
The LM2462 is an integrated high voltage CRT driver circuit
designed for use in color monitor applications. The IC con-
tains three high input impedance, wide band amplifiers
which directly drive the RGB cathodes of a CRT. Each
channel has its gain internally set to −20 and can drive CRT
capacitive loads as well as resistive loads present in other
applications, limited only by the package’s power dissipation.
The IC is packaged in an industry standard 11-lead TO-220
molded plastic power package. See Thermal Considerations
section.
Features
n Higher gain to match LM126X CMOS preamplifiers
n 0V to 3.75V input range
n Stable with 0–20 pF capacitive loads and inductive
peaking networks
n Convenient TO-220 staggered lead package style
n Maintains standard LM240X Family pinout which is
designed for easy PCB layout
Applications
n 1600 x 1200 displays up to 85Hz refresh
n Pixel clock frequencies up to 230 MHz
n Monitors using video blanking
Schematic and Connection Diagrams
DS200376-1
FIGURE 1. Simplified Schematic Diagram
(One Channel)
DS200376-2
Note: Tab is at GND
Top View
Order Number LM2462TA
NS Package Number: TA11B
© 2002 National Semiconductor Corporation DS200376
www.national.com

1 page




LM2462 pdf
Theory of Operation
The LM2462 is a high voltage monolithic three channel CRT
driver suitable for high resolution display applications. The
LM2462 operates with 80V and 12V power supplies. The
part is housed in the industry standard 11-lead TO-220
molded plastic power package.
The circuit diagram of the LM2462 is shown in Figure 1. The
PNP emitter follower, Q5, provides input buffering. Q1 and
Q2 form a fixed gain cascode amplifier with resistors R1 and
R2 setting the gain at −20. Emitter followers Q3 and Q4
isolate the high output impedance of the cascode stage from
the capacitance of the CRT cathode which decreases the
sensitivity of the device to changes in load capacitance. Q6
provides biasing to the output emitter follower stage to re-
duce crossover distortion at low signal levels.
Figure 2 shows a typical test circuit for evaluation of the
LM2462. This circuit is designed to allow testing of the
LM2462 in a 50environment without the use of an expen-
sive FET probe. In this test circuit, the two 2.49kresistors
form a 200:1 wideband, low capacitance probe when con-
nected to a 50coaxial cable and a 50load (such as a
50oscilloscope input). The input signal from the generator
is ac coupled to the base of Q5.
Application Hints
INTRODUCTION
National Semiconductor (NSC) is committed to provide ap-
plication information that assists our customers in obtaining
the best performance possible from our products. The fol-
lowing information is provided in order to support this com-
mitment. The reader should be aware that the optimization of
performance was done using a specific printed circuit board
designed at NSC. Variations in performance can be realized
due to physical changes in the printed circuit board and the
application. Therefore, the designer should know that com-
ponent value changes may be required in order to optimize
performance in a given application. The values shown in this
document can be used as a starting point for evaluation
purposes. When working with high bandwidth circuits, good
layout practices are also critical to achieving maximum per-
formance.
IMPORTANT INFORMATION
The LM2462 performance is targeted for the high end 19“
and 21“ market with resolutions up to 1600 x 1200 and an
85Hz refresh rate. The application circuits shown in this
document were specifically designed to optimize the perfor-
mance of the LM2462 as well as protect it from damage due
to a CRT arc-over. If another member of the LM246X family
is used, please refer to its datasheet.
POWER SUPPLY BYPASS
Since the LM2462 is a wide bandwidth amplifier, proper
power supply bypassing is critical for optimum performance.
Improper power supply bypassing can result in large over-
shoot, ringing or oscillation. 0.1 µF capacitors should be
connected from the supply pins, VCC and VBB, to ground, as
close to the LM2462 as is practical. Additionally, a 47 µF or
larger electrolytic capacitor should be connected from both
supply pins to ground reasonably close to the LM2462.
ARC PROTECTION
During normal CRT operation, internal arcing may occasion-
ally occur. Spark gaps, in the range of 200V, connected from
the CRT cathodes to CRT ground will limit the maximum
voltage, but to a value that is much higher than allowable on
the LM2462. This fast, high voltage, high energy pulse can
damage the LM2462 output stage. The application circuit
shown in Figure 9 is designed to help clamp the voltage at
the output of the LM2462 to a safe level. The clamp diodes,
D1 and D2, should have a fast transient response, high peak
current rating, low series impedance and low shunt capaci-
tance. FDH400 or equivalent diodes are recommended. Do
not use 1N4148 diodes for the clamp diodes. D1 and D2
should have short, low impedance connections to VCC and
ground respectively. The cathode of D1 should be located
very close to a separately decoupled bypass capacitor (C3 in
Figure 9). The ground connection of D2 and the decoupling
capacitor should be very close to the LM2462 ground. This
will significantly reduce the high frequency voltage transients
that the LM2462 would be subjected to during an arcover
condition. Resistor R2 limits the arcover current that is seen
by the diodes while R1 limits the current into the LM2462 as
well as the voltage stress at the outputs of the device. R2
should be a 12W solid carbon type resistor. R1 can be a 14W
metal or carbon film type resistor. Having large value resis-
tors for R1 and R2 would be desirable, but this has the effect
of increasing rise and fall times. Inductor L1 is critical to
reduce the initial high frequency voltage levels that the
LM2462 would be subjected to. The inductor will not only
help protect the device but it will also help optimize rise and
fall times as well as minimize EMI. For proper arc protection,
it is important to not omit any of the arc protection compo-
nents shown in Figure 9.
5 www.national.com

5 Page





LM2462 arduino
Physical Dimensions inches (millimeters) unless otherwise noted
CONTROLLING DIMENSION IS INCH
VALUES IN [ ] ARE MILLIMETERS
NS Package Number TA11B
Order Number LM2462TA
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

11 Page







PáginasTotal 11 Páginas
PDF Descargar[ Datasheet LM2462.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LM246PROGRAMMABLE QUAD BIPOLAR OPERATIONAL AMPLIFIERSSTMicroelectronics
STMicroelectronics
LM2460LM2460 Monolithic Triple Channel High Swing CRT Driver (Rev. B)Texas Instruments
Texas Instruments
LM2460Monolithic Triple Channel High Swing CRT DriverNational Semiconductor
National Semiconductor
LM2462LM2462 Monolithic Triple 3 ns CRT DriverTexas Instruments
Texas Instruments

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar