|
|
PDF DS1800 Data sheet ( Hoja de datos )
| Número de pieza | DS1800 | |
| Descripción | Dual Inverting Log Gain/Attenuator | |
| Fabricantes | Dallas Semiconducotr | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de DS1800 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
DS1800
Dual Inverting Log Gain/Attenuator
www.dalsemi.com
FEATURES
Ultra-low power consumption
Operates from 3V or 5V supplies
Two digitally controlled, 128-position
potentiometers including mute
Logarithmic gain characteristics
Zero-crossing detection eliminates noise
caused by discrete wiper changes
Two control interfaces
- 3-wire serial CPU control
- Pushbutton control
20-pin DIP (300-mil), 20-pin SOIV (300-
mil), and 20-pin (173-mil) TSSOP packaging
available
Operating Temperature Range:
- Industrial: -40°C to +85°C
Software and hardware mute
Standard Resistance Available: 53KΩ
PIN ASSIGNMENT
GND
COUT
CLK
D
RST
ZCEN
MODE
W0
OUT0
IN0
1
2
3
4
5
6
7
8
9
10
20 VCC
19 P1G
18 P1A
17 P0G
16 P0A
15 MUTE
14 AGND
13 IN1
12 OUT1
11 W1
20-Pin DIP (300-mil)
20-Pin SOIC (300-mil)
20-Pin TSSOP
See Mech. Drawings Section
PIN DESCIPTION
OUT0,OUT1 - Low-end of resistor
IN0, IN1 - High-end of resistor
W0,W1
- Wiper Terminal
VCC - 3V or 5V Power Supply Input
RST
CLK
D
COUT
P0G,P1G
P0A,P1A
- Serial Port Reset Input
- Serial Port Clock Input
- Serial Port Data Input
- Cascade Data Output
- Gain Input Pot Controls
- Attenuation Input Pot Controls
ZCEN
MUTE
AGND
GND
- Zero-Crossing Detect Input
- Hardware Mute Control Input
- Analog Ground
- Ground
1 of 14
032000
1 page  
DS1800
Contact closure is defined as the transition from a high level to a low level on these input terminals. The
DS1800 interprets input pulse widths as the means of controlling wiper movement. A single pulse input
over the PxA or PxG input terminals will cause the wiper to move one position. A transition from high to
low on these inputs is considered the beginning of pulse activity or contact closure. The DS1800 has two
timing modes for controlling the speed at which pushbuttons will operate. These modes are termed fast
mode operation and slow mode operation.
In slow mode operation, a single pulse is defined as being greater than 1 ms but lasting no longer than 0.8
seconds. Correspondingly, in fast mode operation, a single pulse is defined as being greater than 50 µs
but lasting no longer than 0.8 second.
Repetitive pulsed inputs can be used to step through each resistive position of the device in a relatively
fast manner. The timing requirements for repetitive pulsed inputs is that pulses must be separated by a
minimum time of 1 ms for slow mode operation and 50 µs for fast mode operation.
Pulse inputs lasting longer than 0.8 seconds will cause the wiper to move one position every 25 ms
seconds after the initial 0.8 second hold time. This is true regardless of the mode input. The total time
required to transcend the entire potentiometer using a continuous input pulse is given by the following
formula:
0.8(seconds) + 127 x 25 ms = 3.975(seconds)
SLOW MODE AND FAST MODE OPERATION
Pushbutton operation, as mentioned, can be operated at two distinct speeds or modes; fast and slow. The
mode or speed of pushbutton debounce is determined at device power-up by the state of the MODE pin.
When MODE powers to a high state, pushbutton debounce timing will operate at the slow mode rate.
When powered and in the low state, debounce timing operates at the fast rate. Timing specifications for
pushbutton operation can be found in the AC Electrical Specification Table for pushbutton operation.
Timing diagrams for pushbutton operation can be found in Figure 7.
ZERO CROSSING DETECTION
The DS1800 provides a zero-crossing detection capability when using the 3-Wire serial interface. Zero-
crossing detection provides a means for minimizing unwanted audible noise that may result from sizable
discrete wiper transitions when using the part in audio applications. The zero-crossing detect feature
allows independent wiper changes only when the two terminals of the potentiometer(s) have equal
potentials and within a 50 ms time window from the fall of the RST signal. If at 50 ms the DS1800 has
not detected a zero-crossing, the wiper position of the potentiometer(s) will change regardless of the state
of the input signal. Zero-crossing detection is activated when the ZCEN input is in a low-state. When high,
the ZCEN input deactivates both the 50 ms time requirement and zero-crossing detection.
Zero-crossing detection is also available when using the part in pushbutton operation. When a pushbutton
is activated, the part will change wiper position during the first detected zero-crossing or at the end of a
50 ms time window.
When operating in pushbutton operation with a continuous input pulse, the wiper position will change
once during the initial 0.8-second time period. This change is dictated by a detected zero-crossing or 50
ms time window. Subsequent changes when operating with a continuous input pulse occur on 25 ms time
intervals and are dependent on zero-crossings or 50 ms time-outs.
5 of 14
5 Page 
RECOMMENDED CIRCUIT CONFIGURATION Figure 2
DS1800
VO /VI GAIN/ATTENUATION VS. POSITION RELATIONSHIP Figure 3
11 of 14
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet DS1800.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| DS1800 | Dual Inverting Log Gain/Attenuator | Dallas Semiconducotr |
| DS1800-3 | AC-DC / Distributed Power Front-End 1U |  Emerson |
| DS1801 | Dual Audio Taper Potentiometer | Dallas Semiconducotr |
| DS1802 | Dual Audio Taper Potentiometer With Pushbutton Control | Dallas Semiconducotr |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |