|
|
Número de pieza | UC3726 | |
Descripción | Isolated Drive Transmitter | |
Fabricantes | Unitrode | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de UC3726 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! Isolated Drive Transmitter
UC1726
UC2726
UC3726
FEATURES
• 750mA Output Drive, Source or Sink
• 8 to 35V Operation
• Transmits Drive Logic and Power
through Low Cost Transformer
• Programmable Operating Frequency
• Up to 750kHz Operation
• Improved Output Control Algorithm
Minimizes Output Jitter
• Fault Logic Monitors Isolated High
Side IGBT Driver UC1727 for Faults
• User Programmable Fault Timing
Screens False Fault Signals
• Shutdown Mode Disables On Chip
Logic Reference for Low Standby
Power
• Optional External Biasing of Logic
Circuitry can Reduce Overall Power
Dissipation
BLOCK DIAGRAM
DESCRIPTION
The UC1726 Isolated Drive Transmitter, and its companion chip, the
UC1727 Isolated High Side IGBT Driver, provide a unique solution to driv-
ing isolated power IGBTs. They are particularly suited to drive the high
side devices on a high voltage H-bridge. The UC1726 device transmits
the drive logic and drive power, along with transferring and receiving fault
information with the isolated gate circuit using a low cost pulse trans-
former.
This drive system utilizes a duty cycle modulation technique that gives in-
stantaneous response to the drive control transitions, and reliably passes
steady state, or DC conditions. High frequency operation, up to 750kHz,
allows the cost and size of the coupling transformer to be minimized.
The UC1726 can be powered from a single VCC supply which internally
generates a voltage reference for the logic circuitry. It can also be placed
into a low power shutdown mode that disables the internal reference. The
IC’s logic circuitry can be powered from an external supply, VL, to mini-
mize overall power dissipation. Fault logic monitors the Isolated High Side
IGBT Driver UC1727 for faults. Based on user defined timing, the
UC1726 distinguishes valid faults, which it responds to by setting the fault
latch pin. This also disables the gate drive information until the fault reset
pin is toggled to a logic one.
The UC1726 operates over an 8 to 35 volt supply range. The typical VCC
voltage will be greater than 28 volts to be compatible with the UC1727.
The undervoltage lockout circuitry of the Isolated High Side IGBT Driver
UC1727 locks out the drive information during its undervoltage lockout.
7/95
UDG-94004-1
1 page OPERATING FREQUENCY:
The chip operating frequency is determined by the values
of components connected to the RT and CT pins. A resis-
tor connected between RT and ground sets the charge
current to ICT = VL / 4RT. The operating frequency varies
slightly depending on the VCC and VL voltages. The fol-
lowing equations approximate the one shot pulse width at
operating frequency when VCC = 20V.
UC1726
UC2726
UC3726
TPW = 1.1RT(CT + 50pF)
FO
=
1
3.3RT(CT
+
50pF)
The 50pF additional capacity represents internal chip ca-
pacitance at the CT input.
TYPICAL APPLICATION
IF FAULT LOGIC NOT USED, GROUND FAULT PIN.
UDG-94006
UNITRODE INTEGRATED CIRCUITS
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 • FAX (603) 424-3460
5
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet UC3726.PDF ] |
Número de pieza | Descripción | Fabricantes |
UC3724 | Isolated Drive Transmitter | Unitrode |
UC3724 | Isolated Drive Transmitter | Texas Instruments |
UC3725 | Isolated High Side FET Driver | Unitrode |
UC3725 | Isolated High Side FET Driver (Rev. A) | Texas Instruments |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |