DataSheet.es    


PDF IC25N010ATDA04 Data sheet ( Hoja de datos )

Número de pieza IC25N010ATDA04
Descripción ATA / IDE Hard Disk Drive
Fabricantes IBM 
Logotipo IBM Logotipo



Hay una vista previa y un enlace de descarga de IC25N010ATDA04 (archivo pdf) en la parte inferior de esta página.


Total 2 Páginas

No Preview Available ! IC25N010ATDA04 Hoja de datos, Descripción, Manual

IBM storage products
ibm
Quick installation guide
Travelstar 48GH, 30GN & 15GN
2.5 inch ATA/IDE hard disk drive
Models: IC25T048ATDA05
IC25N030ATDA04
IC25N020ATDA04
IC25N015ATDA04
IC25N012ATDA04
IC25N010ATDA04
IC25N007ATDA04
IC25N006ATDA04
IC25N005ATDA04
Handling precautions
! Wear a wrist strap while handling the drive to pre-
vent damage from Electrostatic Discharge (ESD).
! Set the drive down gently to prevent damage from
impact or vibration.
! Do not open the ESD bag containing the drive until
needed.
! Handle the drive carefully by the edges. Do not
touch the exposed printed circuit board or any
electronic components.
! Do not press on the top or bottom of the drive.
! Do not cover the drive’s breather hole.
Attach the drive
For instructions on how to complete the physical instal-
lation of the drive consult your system manual.
Jumper settings
A1. A2. A3. A4. A5.
Pin 1
djsa_qi1.prz
Quick installation*
IMPORTANT: Back up all data before proceeding with
installation!
*It is important to note that the use of Travelstar drives in
some notebooks will require reuse of unique hardware
(for example — mounting trays, connecting cable,
insulating material). If in doubt please consult your
notebook manufacturer as this operation may require a
qualified technician.
Set the jumpers
! Master drive. No jumper is required if the drive is
the only drive in a system or the Master drive in a
two-drive system.
! Slave drive. If the drive is the Slave drive in a two-
drive system, jumper setting A2 is required. See A2
setting in illustration
! Cable Select. Consult the system manual to see if
your computer supports Cable Select before choos-
ing the A3 jumper setting. See Illustration.
A1. Master A2. Slave
A3. Cable Select
A4. Never Attach a Jumper Here!
A5. Never Attach a Jumper Here!
Configure your computer
1. Turn on your computer. Your computer may detect a
configuration change and prompt you to proceed to
the Setup screen.
2. If your computer does not prompt you to reconfigure,
enter your computer’s Setup, usually by key selection
or keyboard combinations during power-on or during
a reboot. Refer to your system manual for the proper
key sequence. If the computer fails to boot up, power
off, remove the drive, and return your system to its
original configuration. Reboot and enter your com-
puter’s Setup. Follow the directions in step 3, then
attach the drive.
3. Select Auto Detect if your computer Setup supports
this feature. If your computer does not support Auto
Detect, select the appropriate UDT (User Definable
Type) for the drive.
IBM Technology Group Support Center
Page 1
version 2.0

1 page





PáginasTotal 2 Páginas
PDF Descargar[ Datasheet IC25N010ATDA04.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
IC25N010ATDA04ATA / IDE Hard Disk DriveIBM
IBM

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar