|
|
PDF TA0016 Data sheet ( Hoja de datos )
| Número de pieza | TA0016 | |
| Descripción | EUROPEAN APPLICANTIONS FOR RF 403 CORDLESS TELEPHONE FRONT END RFIC | |
| Fabricantes | RF | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TA0016 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
TA0016
TA0016
RF2403: European Applications for RF2403 Cordless Telephone Front
End RFIC
A front end RFIC for cordless telephone applications
has been developed for use in the 902MHz to 928MHz
ISM (Industrial-Scientific-Medical) band in the United
States under Part 15 of the FCC Rules. Potential appli-
cations for this RFIC in this frequency band include
cordless telephones, wireless LANs, wireless security
systems and point-of-sale (POS) terminals.
This RFIC, the RF2403, consists of a single-stage
LNA, a two-stage PA with 21dBm of output power and
a transmit/receive switch. The RFIC is built using a
commercial GaAs MESFET process, and is packaged
in a SOP-16 narrowbody surface-mount package. The
circuit operates with a +5.0V supply, and has separate
enable lines which control the bias to the transmit and
receive functions. All bias and control signals operate
with voltages which lie between ground potential and
VDD. With both enable lines at logic low, the circuit is in
a “power down” mode in which it draws approximately
1.0mA of leakage current from the VDD supply. Some
external passive components are required, primarily for
DC blocking and RF bypassing functions. The PA out-
put impedance matching circuitry, consisting of a pi-
network, is realized using external passive compo-
nents in order to both conserve die area and to reduce
parasitic losses. This same RFIC has been evaluated
for use in 433MHz European applications, and has
been found to have very good RF performance there.
Although no changes have been made to the RFIC
itself, several changes to the application circuit are
necessary for operation at 433MHz. Table 1 shows the
component values for both versions of the RF2403
application circuit. The two application schematics are
shown, for 433MHz operation and for 915MHz opera-
tion, in Figures 1 and 2, respectively. The resulting RF
performance for these circuits is shown in Table 2. The
I/O port return losses are somewhat degraded at
433MHz, primarily due to the excess reactance of the
on-chip DC blocking capacitors in the RFIC. The
RF2403 does have comparable gain, output power and
linearity at 433MHz with respect to its performance at
915 MHz.
RF Specification
LNA Gain1
LNA NF1
LNA
P1
1
dB
RX IRL, ANT port1
LNA ORL
PA Small Signal Gain1
PA P1dB1
PA IRL
PA ORL, ANT port1
PA Two-tone POUT1,2
@ -25dBc IMD3
Measured Performance (All Typical) @VDD=5.0V
433MHz Circuit
915MHz Circuit
17 dB
16 dB
2.4 dB
2.7 dB
+6.0 dBm
+6.0 dBm
6.0 dB
9.0 dB
15 dB
28 dB
13 dB
28 dB
19.0 dBm
21.0 dBm
11 dB
11.5 dB
17 dB
10.5 dB
17.5 dBm
16.7 dBm
Table 2. RF2403 measured performance, using the two application schematics
Note 1: Performance is measured through the monolithic T/R switch
Note 2: f1=432.5MHz, f2=433.5MHz, or, f1=914.5MHz, f2=915.5MHz
13
Copyright 1997-2000 RF Micro Devices, Inc.
13-85
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet TA0016.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TA0012 | High Efficiency HBT GSM Power Amplifier |  RF Micro Devices |
| TA0016 | EUROPEAN APPLICANTIONS FOR RF 403 CORDLESS TELEPHONE FRONT END RFIC | RF |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |