DataSheet.es    


PDF LC86F3264A Data sheet ( Hoja de datos )

Número de pieza LC86F3264A
Descripción 8 Bit Single Chip Microcontroller
Fabricantes Sanyo 
Logotipo Sanyo Logotipo



Hay una vista previa y un enlace de descarga de LC86F3264A (archivo pdf) en la parte inferior de esta página.


Total 23 Páginas

No Preview Available ! LC86F3264A Hoja de datos, Descripción, Manual

8-BIT SINGLE CHIP MICROCONTROLLER
Preliminary
LC86F3264A
LC86F3264A
8-bit Single Chip Microcontroller with on-chip 96K-byte Flash Memory (ROM 64K-byte + CGROM 16K-byte +
Extended ROM 16k-byte), on-chip 640-byte RAM and 352 × 9 bit Display RAM
Overview
The LC86F3264A is a CMOS 8-bit single chip microcontroller with Flash Memory for the LC863200series. This
microcontroller contains the following on-chip functional blocks:
- CPU : Operable at a minimum bus cycle time of 0.424µs
- On-chip ROM capacity
: 96K bytes Flash Memory
Program ROM
: 64K bytes
CGROM
: 16K bytes
Extended ROM
: 16K bytes
- On-chip RAM capacity : 640 bytes
- Display RAM : 352 × 9 bits
- Closed-Caption TV controller and the on-screen display controller
- Closed-Caption data slicer
- Four channels × 8-bit AD Converter
- Three channels × 7-bit PWM
- Two 16-bit timer/counters, 14-bit base timer
- 8-bit synchronous serial interface circuit
- IIC-bus compliant serial interface circuit (Multi-master type)
- ROM correct function
- 16-source 10-vectored interrupt system
- Integrated system clock generator and display clock generator
Only one X’tal oscillator (32.768kHz) for PLL reference is used for both generators
All of the above functions are fabricated on a single chip.
The program is rewritable by using the on-board writing system after the LSI has been installed on
the application board.
No products described or contained herein are intended for use in surgical implants, life-support systems,
aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the
like, the failure of which may directly or indirectly cause injury, death or property loss.
Anyone purchasing any products described or contained herein for an above-mentioned use shall :
1) Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates,
subsidiaries and distributors and all their officers and employees, jointly and severally, against any
and all claims and litigation and all damages, cost and expenses associated with such use :
2) Not impose any responsibility for any fault or negligence which may be cited in any such claim or
litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of
their officers and employees jointly or severally.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no
guarantees are made or implied regarding its use or any infringements of intellectual property rights or other
rights of third parties.
Note : This product includes the IIC bus interface circuit. If you intend to use the IIC bus interface, please
notify us of this in advance of our receiving your program ROM code order.
Purchase of SANYO IIC components conveys a license under the Philips IIC Patents Rights to use these
components in an IIC system, provided that the system conforms to the IIC Standard Specification as
defined by Philips.
Trademarks
IIC is a trademark of Philips Corporation.
This production is produced and sold by SANYO under license of the Silicon Storage Technology Inc.
This catalog provides information as of December 2000. Specifications and information herein are subject to
change without notice.
SANYO Electric Co., Ltd. Semiconductor Company
SYSTEM-LSI Div. System-Microcomputer Development Dep.
1-1-1, Sakata Oizumi-Machi, Gunma, JAPAN
Ver.1.00
SYSTEM-LSI 2000-12-27 M.Sato
1/23

1 page




LC86F3264A pdf
LC86F3264A
Feed the Port 0 interrupt condition
(19) Applicable mask ROM version
- LC863264 / LC863256/ LC863248 / LC863240 / LC863232 / LC863228 / LC863224 / LC863220 /
LC863216
(20) Package
- DIP42S
- QIP48E
(21) Development tools
- Evaluation chip:
- Emulator:
LC863096
EVA86000(main) + ECB863200(evaluation chip board)
+ POD863200(pod:DIP42S) or POD863201(QIP48E)
Write Flash Memory
SANYO provides special services including writing data to Flash Memory and stamping.
for these services.
Please feel free to ask our sales persons for details.
There is a charge
Ver.1.00
5/23

5 Page





LC86F3264A arduino
On-board writing system
LC86F3264A
The LC86F3264A has the On-board writing system. The program is renewable by using SANYO Flash On-board
System after the LSI has been installed on the application board.
This system is composed of 4 types divided by the combination of the mode setting pin and communication pin.
Each type system has to connect the 6 pins (VDD, VSS, RES, communication pins) with the interface board of
SANYO Flash On-board System.
It is necessary that the pins to be used for the rewriting system should be able to be separated from the
application board properly.
The system type is selected by the option setting program (Su86K.exe).
types
type1
type2
type3
type4
mode setting pin
RES pin (high voltage(12V) applied)
RES pin (high voltage(12V) applied)
P00 pin (High level voltage applied)
P00 pin (High level voltage applied)
communication pins
P00(DATA1),P01(DATA0),P02(CLK)
P00(DATA1),P60(DATA0),P61(CLK)
P00(ENA/DATA1),P01(DATA0),P02(CLK)
P00(ENA/DATA1),P60(DATA0),P61(CLK)
• Type 3 or 4 is selected : P00 is exclusive for the on-board system. This pin must always be pulled-down, so
this pin can’t be used for other applications.
Please set P00 pin N-channel open drain output.•option setting•
In the user program, “0” is always set to the P00 latch (bit 0 in the Port 0 latch
(140h)) because the P0 interrupt must not be requested on the P00 pin .
• The loader program must be written into the ROM to use On-board writing system.
The loader program should be written into the ROM before the LSI has been installed on the board by the
the general purpose PROM programs.
When the option setting selects the this system to use, the loader program automatically links to the extended
ROM field(14000h-147FFh) on the user program linking.
Please ask to our sales persons before using On-board writing system.
Use of PROM Conversion board
When reading or writing data to the LC86F3264A using our exclusive conversion board (W86F3264D,
W86F3264Q) general purpose PROM programs can be used.
(1) Name of conversion boards
- W86F3264D • • • DIP42S purpose
- W86F3264Q • • • QIP48E purpose
(2) Available PROM programs
The LC86F3264A does not support a silicon signature feature.
type selection) when programming this device.
Do not use the feature (automatic device
For the address range, 0 to 17FFFh should be specified (fixed data ‘00’ is read if 1800h to 1FFFFh is
specified).
Single word write
Manufacture
Name of device
Minato Electronics
Ando
Data I. O.
MODEL 1890A + OU-910
AF-9708
ChipLab
version
V4.1
01.00
V5.3
applicable device (code)
SST Co., Ltd. 29EE010 (D734)
SST Co., Ltd. 29EE010 (47101)
SST Co., Ltd. 29EE010
Data protection
setting after write
operation
Protected
Protected
Selectable
Ver.1.00
11/23

11 Page







PáginasTotal 23 Páginas
PDF Descargar[ Datasheet LC86F3264A.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LC86F3264A8 Bit Single Chip MicrocontrollerSanyo
Sanyo

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar