DataSheet.es    


PDF DS1238A Data sheet ( Hoja de datos )

Número de pieza DS1238A
Descripción MicroManager
Fabricantes Dallas 
Logotipo Dallas Logotipo



Hay una vista previa y un enlace de descarga de DS1238A (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! DS1238A Hoja de datos, Descripción, Manual

www.dalsemi.com
DS1238A
MicroManager
FEATURES
Holds microprocessor in check during power
transients
Halts and restarts an out-of-control
microprocessor
Warns microprocessor of an impending power
failure
Converts CMOS SRAM into nonvolatile
memory
Unconditionally write protects memory when
power supply is out of tolerance
Delays write protection until completion of
the current memory cycle
Consumes less than 200 nA of battery current
Controls external power switch for high
current applications
Debounces pushbutton reset
Accurate 10% power supply monitoring
Optional 5% power supply monitoring
designated DS1238A-5
Provides orderly shutdown in microprocessor
applications
Pin-for-pin compatible with MAX691
Standard 16-pin DIP or space-saving 16-pin
SOIC
Optional industrial temperature range -40°C
to +85°C
PIN ASSIGNMENT
VBAT 1 16 RST
VCCO
VCC
GND
PF
RVT
OSCIN
OSCSEL
2
3
4
5
6
7
8
15 RST
14 WDS
13 CEI
VBAT
VCCO
12 CEO
VCC
11 ST
GND
PF
10 NMI
RVT
OSCIN
9 IN OSCSEL
1 16
2 15
3 14
4 13
5 12
6 11
7 10
89
RST
RST
WDS
CEI
CEO
ST
NMI
IN
16-Pin DIP (300-mil)
See Mech. Drawings Section
16-Pin SOIC (300-mil)
See Mech. Drawings Section
PIN DESCRIPTION
VBAT
VCCO
VCC
GND
- +3-Volt Battery Input
- Switched SRAM Supply Output
- +5-Volt Power Supply Input
- Ground
PF - Power-Fail
RVT - Reset Voltage Threshold
OSCIN
- Oscillator In
OSCSEL - Oscillator Select
IN - Early Warning Input
NMI - Non-Maskable Interrupt
ST - Strobe Input
CEO - Chip Enable Output
CEI - Chip Enable Input
WDS - Watchdog Status
RST - Reset Output (active low)
RST - Reset Output (active high)
DESCRIPTION
The DS1238A MicroManager provides all the necessary functions for power supply monitoring, reset
control, and memory backup in microprocessor-based systems. A precise internal voltage reference and
comparator circuit monitor power supply status. When an out-of-tolerance condition occurs, the
microprocessor reset and power-fail outputs are forced active, and static RAM control unconditionally
write protects external memory. The DS1238A also provides early warning detection of a user-defined
threshold by driving a non-maskable interrupt. External reset control is provided by a pushbutton reset
1 of 13
111899

1 page




DS1238A pdf
OSCILLATOR CONTROLS Table 1
Watchdog Timeout Period (typ)
OSCIN OSCSEL
First Period
Following a Reset
Other Timeout
External Ext Clk
Low
20480 Clks
5120 Clocks
Ext Cap Low
2.2 sec
47 pf
X Cpf
550 ms
47 pf
X Cpf
Internal Low Hi/Open
Hi/Open Hi/Open
2.7 sec
2.7 sec
170 ms
2.7 sec
Note that the OSCIN and OSCSEL pins are tri-stated when VCC is below VBAT.
DS1238A
Reset Active
Duration
641 Clks
69 ms
47 pf
X Cpf
85 ms
85 ms
POWER MONITOR, WATCHDOG TIMER, AND PUSHBUTTON RESET Figure 3
PUSHBUTTON RESET TIMING Figure 4
5 of 13

5 Page





DS1238A arduino
ABSOLUTE MAXIMUM RATINGS*
Voltage on VCC Pin Relative to Ground
Voltage on I/O Relative to Ground
Operating Temperature
Operating Temperature (Industrial Version)
Storage Temperature
Soldering Temperature
-0.5V to +7.0V
-0.5V to VCC + 0.5V
0°C to 70°C
-40°C to +85°C
-55°C to +125°C
260°C for 10 seconds
DS1238A
* This is a stress rating only and functional operation of the device at these or any other conditions
above those indicated in the operation sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
PARAMETER
SYMBOL MIN
TYP
Supply Voltage
VCC 4.5 5.0
Supply Voltage (5% Option)
VCC 4.75 5.0
Input High Level
VIH 2.0
Input Low Level
VIL -0.3
IN Input Pin
VIN 0
Battery Input
VBAT
0
MAX
5.5
5.5
VCC+0.3
+0.8
VCC
4.0
(0°C to 70°C)
UNITS NOTES
V1
V1
V1
V1
V1
V1
DC ELECTRICAL CHARACTERISTICS
PARAMETER
SYMBOL MIN
(0°C to 70°C; VDD= 5V ± 10%)
TYP MAX UNITS NOTES
Supply Current
ICC
4 mA 2
Battery Current
IBAT
0
200 nA 2, 12
Supply Output Current
(VCCO = VCC - 0.3V)
ICC01
100 mA
3
Supply Out Current (VCC < VBAT)
ICC02
1 mA 4
Supply Output Voltage
VCCO
VCC-0.3
V1
Battery Back Voltage
VCCO
VBAT-0.8
V6
Low Level @ RST
VOL
0.4 V
1
Output Voltage @ -500 µA
VOH VCC-0.5V VCC-0.1V
V1
CEO and PF Output
VOHL
VBAT-0.8
V6
Input Leakage Current
ILI -1.0
+1.0 µA
2
Output Leakage Current
ILO -1.0
+1.0 µA
11
Output Current @ 0.4V
IOL
4.0 mA
9
Output Current @ 2.4V
IOH -1.0
mA 10
Power Sup. Trip Point
VCCTP 4.25 4.37 4.50 V
1
Power Supply Trip (5% Option)
VCCTP
4.50
4.62
4.75
V
IN Input Pin Current
ICCIN
-1.0
+1.0 µA
IN Input Trip Point
VTP 1.15 1.27 1.35 V
1
11 of 13

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet DS1238A.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
DS1238MicroManagerDallas
Dallas
DS1238AMicroManagerDallas
Dallas

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar