DataSheet.es    


PDF SA1620 Data sheet ( Hoja de datos )

Número de pieza SA1620
Descripción Low voltage GSM front-end transceiver
Fabricantes Philips 
Logotipo Philips Logotipo



Hay una vista previa y un enlace de descarga de SA1620 (archivo pdf) en la parte inferior de esta página.


Total 26 Páginas

No Preview Available ! SA1620 Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
SA1620
Low voltage GSM front-end transceiver
Product specification
Supersedes data of 1996 Oct 08
IC17 Data Handbook
1997 May 22
Philips
Semiconductors

1 page




SA1620 pdf
Philips Semiconductors
Low voltage GSM front-end transceiver
Product specification
SA1620
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
RATING
UNITS
VCCXX
VBATT
VIN
V
VG
Supply voltages
Battery voltage
Voltage applied to any other pin
VCCTx1,2 pins to VCCBM
Any GND pin to any other GND pin
-0.3 to +6.0
-0.3 to +8.0
-0.3 to (VCCXX+0.3)
-0.3 to +1
0
V
V
V
V
V
PD Power dissipation, TA = 25°C (still air)
800 mW
TJMAX
Maximum operating junction temperature
150 °C
PMAX
Maximum power input/output
+20 dBm
TSTG
Storage temperature range
–65 to +150
°C
VTXO, VTXOX Positive RF peak voltage at Tx outputs
6V
VRXIF, VRXIFX Positive IF peak voltage at Rx mixer outputs
6V
NOTE:
1. Maximum junction temperature is determined by the power dissipation is determined by the operating ambient temperature and the thermal
resistance, θJA. 48-pin TQFP: θJA = 67°C/W.
DC REGULATORS
Two low drop regulators (REG1 and REG2) are included on the chip
and may be used to deliver the supply voltage of the main circuitry
(e.g., 3V) out of the battery (at VBATT = 3.3 to 7.5V) as shown in
Figure 4 and in Table 1.
REG1 is intended to supply, at least, the internal functions of the
SA1620. Both regulators may also be used for external circuitry.
For this application, different voltages may be programmed as
shown in Table 1.
The transmitter supply pins (VCCTx1,2) also operate as a sensor
connection in the feedback loop of REG1 and must be externally
connected to pin VREG1. For REG2, the sensor pin VREGF2 must
be connected to VREG2.
All ground pins are internally bonded to the header except for pins
GNDL1, GNDREG1 and GNDREG2.
When both regulators are not used, connect pins VBATT, PON,
CON1, CON2, VREG1, VREG2 and VREG2F2 to ground.
Table 1. DC Reg Output Voltage Control Pins
CON1 CON2
VREG1
VREG2
UNITS
L L 3 ± 5%
3 ± 5%
V
L H 3.4 ± 5% 3.4 ± 5% V
H
L
3.7 ± 5%
3.7 ± 5%
V
H
H
5.1 ± 5%
5.1 ± 10%
V
NOTES:
1. Logic levels at CON1 and CON2:
H – Open circuit. Pin must not be connected externally.
Logic high level supplied on chip.
L – Connected to ground.
2. Currents at CON1 and CON2:
H – 0µA
L (PON = H) – 50µA
L (PON = L) – <1µA
1997 May 22
5

5 Page





SA1620 arduino
Philips Semiconductors
Low voltage GSM front-end transceiver
Product specification
SA1620
1997 May 22
Figure 3.
11
SR00130

11 Page







PáginasTotal 26 Páginas
PDF Descargar[ Datasheet SA1620.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
SA1620Low voltage GSM front-end transceiverPhilips
Philips
SA1620BELow voltage GSM front-end transceiverPhilips
Philips
SA1622AUDIO PREAMPLIFIERSilan Microelectronics
Silan Microelectronics
SA1622AAUDIO PREAMPLIFIERSilan Microelectronics
Silan Microelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar