|
|
Número de pieza | OP176 | |
Descripción | Bipolar/JFET / Audio Operational Amplifier | |
Fabricantes | Analog Devices | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de OP176 (archivo pdf) en la parte inferior de esta página. Total 21 Páginas | ||
No Preview Available ! a
Bipolar/JFET,
Audio Operational Amplifier
OP176*
FEATURES
Low Noise: 6 nV/√Hz
High Slew Rate: 25 V/µs
Wide Bandwidth: 10 MHz
Low Supply Current: 2.5 mA
Low Offset Voltage: 1 mV
Unity Gain Stable
SO-8 Package
APPLICATIONS
Line Driver
Active Filters
Fast Amplifiers
Integrators
GENERAL DESCRIPTION
The OP176 is a low noise, high output drive op amp that
features the Butler Amplifier front-end. This new front-end
design combines both bipolar and JFET transistors to attain
amplifiers with the accuracy and low noise performance of
bipolar transistors, and the speed and sound quality of JFETs.
Total Harmonic Distortion plus Noise equals previous audio
amplifiers, but at much lower supply currents.
Improved dc performance is also provided with bias and offset
currents greatly reduced over purely bipolar designs. Input
offset voltage is guaranteed at 1 mV and is typically less than
*Protected by U.S. Patent No. 5101126.
PIN CONNECTIONS
8-Lead Narrow-Body SO
(S Suffix)
8-Lead Epoxy DIP
(P Suffix)
NULL 1
–IN 2
+IN 3
V– 4
OP176
8 NC
7 V+
6 OUT
5 NULL
NULL 1
–IN 2
+IN 3
V– 4
OP176
OP-482
8 NC
7 V+
6 OUT
5 NULL
200 µV. This allows the OP176 to be used in many dc coupled
or summing applications without the need for special selections
or the added noise of additional offset adjustment circuitry.
The output is capable of driving 600 Ω loads to 10 V rms while
maintaining low distortion. THD + Noise at 3 V rms is a low
0.0006%.
The OP176 is specified over the extended industrial (–40°C to
+85°C) temperature range. OP176s are available in both plastic
DIP and SO-8 packages. SO-8 packages are available in 2500
piece reels. Many audio amplifiers are not offered in SO-8
surface mount packages for a variety of reasons, however, the
OP176 was designed so that it would offer full performance in
surface mount packaging.
7
RB2
QB4
RB4
RB3
QB5
RB5
QB6
RB7
RB6
QB7
CB1
QB3
J1
Q1
2
Z2
J2
Q2
3
JB1
QB2
RB1
Q3
Q5
QB1
Z1
R1L R1P1
QB8
CC1
R1A R1P2
R1S R2S
Q4 QS3
R2P1 R2L
R2P2 R2A
CCB
Q6
CF
R3
QB9
R4
Q9
CC2
Q8
Q10
RS1
Q11
QS1
R5
RS2
QS2
6
Q7
15
4
REV. 0
Simplified Schematic
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
1 page 80
70
SINK
60
±VS = ±15V
50 SOURCE
40
30
20
10
0
–50
–25
0 25 50
TEMPERATURE – °C
75 100
Figure 7. Short Circuit Current vs. Temperature @ ±15 V
120
100
80
60
40
20
0
–20
–40
–60
1k
GAIN
TA = +25°C
VS = ±15V
RL = >600Ω
PHASE
PHASE MARGIN = 60°
90
135
180
225
10k 100k
1M
10M
100M
FREQUENCY – Hz
Figure 8. Open-Loop Gain & Phase vs. Frequency
50
40
30
20
10
0
–10
–20
–30
1k
TA = +25°C
VS = ±15V
10k 100k
1M
FREQUENCY – Hz
10M
100M
Figure 9. Closed-Loop Gain vs. Frequency
OP176
120
TA = +25°C
100
+PSRR
±VS = ±15V
80
60 –PSRR
40
20
0
100
1k 10k 100k
FREQUENCY – Hz
1M
Figure 10. Power Supply Rejection vs. Frequency
2000
1750
1500
±VS = ±15V
±VO = ±10V
1250
1000
750
500
250
0
–50
–25
Ω–GAIN, RL = 2kΩ
+GAIN, RL = 2kΩ
–GAIN, RL = 600Ω
+GAIN, RL = 600Ω
0 25 50
TEMPERATURE – °C
75
100
Figure 11. Open-Loop Gain vs. Temperature
40
TA = +25°C
VS = ±15V
30
AV = +100
20
10 AV = +10
0
100
AV = +1
1k 10k 100k
FREQUENCY – Hz
1M
Figure 12. Closed-Loop Output Impedance vs. Frequency
REV. 0
–5–
5 Page OP176
Attention to Source Impedances Minimizes Distortion
Since the OP176 is a very low distortion amplifier, careful
attention should be given to source impedances seen by both
inputs. As with many FET-type amplifiers, the p-channel
JFETs in the OP176’s input stage exhibit a gate-to-source
capacitance that varies with the applied input voltage. In an
inverting configuration, the inverting input is held at a virtual
ground and, as such, does not vary with input voltage. Thus,
since the gate-to-source voltage is constant, there is no distor-
tion due to input capacitance modulation. In noninverting
applications, however, the gate-to-source voltage is not
constant. The resulting capacitance modulation can cause
distortion above 1 kHz if the input impedance is > 2 kΩ and
unbalanced.
Figure 36 shows some guidelines for maximizing the distortion
performance of the OP176 in noninverting applications. The
best way to prevent unwanted distortion is to ensure that the
parallel combination of the feedback and gain setting resistors
(RF and RG) is less than 2 kΩ. Keeping the values of these
resistors small has the added benefits of reducing the thermal
noise of the circuit and dc offset errors. If the parallel combina-
tion of RF and RG is larger than 2 kΩ, then an additional
resistor, RS, should be used in series with the noninverting
RG RF
RS* OP176
VOUT
VIN
* RS = RG//RF IF RG//RF > 2kΩ
FOR MINIMUM DISTORTION
Figure 36. Balanced Input Impedance to Mininize
Distortion in Noninverting Amplifier Circuits
input. The value of RS is determined by the parallel combina-
tion of RF and RG to maintain the low distortion performance of
the OP176. For a more generalized treatment on circuit
impedances and their effects on circuit distortion, please review
the section on Active Filters at the end of the Applications
section.
Driving Capacitive Loads
As with any high speed amplifier, care must be taken when
driving capacitive loads. The graph in Figure 14 shows the
OP176’s overshoot versus capacitive load. The test circuit is a
standard noninverting voltage follower; it is this configuration
that places the most demand on an amplifier’s stability. For
capacitive loads greater than 400 pF, overshoot exceeds 40%
and is roughly equivalent to a 45° phase margin. If the applica-
tion requires the OP176 to drive loads larger than 400 pF, then
external compensation should be used.
Figure 37 shows a simple circuit which uses an in-the-loop
compensation technique that allows the OP176 to drive any
capacitive load. The equations in the figure allow optimization
of the output resistor, RX, and the feedback capacitor, CF, for
optimal circuit stability. One important note is that the circuit
bandwidth is reduced by the feedback capacitor, CF, and is
given by:
BW = 1
2 π R F CF
RG
VIN
RF
CF
OP176
RX
VOUT
CL
RX = RO RG WHERE RO = OPEN-LOOP OUTPUT RESISTANCE
RF
[ ]( )I
CF =
I+
| ACL|
( )RF + RG
RF
CL RO
Figure 37. In-the-Loop Compensation Technique for
Driving Capacitive Loads
APPLICATIONS USING THE OP176
A High Speed, Low Noise Differential Line Driver
The circuit of Figure 38 is a unique line driver widely used in
many applications. With ± 18 V supplies, this line driver can
deliver a differential signal of 30 V p-p into a 2.5 kΩ load. The
high slew rate and wide bandwidth of the OP176 combine to
yield a full power bandwidth of 130 kHz while the low noise
front end produces a referred-to-input noise voltage spectral
density of 15 nV/√Hz. The circuit is capable of driving lower
impedance loads as well. For example, with a reduced output
level of 5 V rms (14 V p-p), the circuit exhibits a full-power
bandwidth of 190 kHz while driving a differential load of 249 Ω!
The design is a transformerless, balanced transmission system
where output common-mode rejection of noise is of paramount
importance. Like the transformer-based design, either output
can be shorted to ground for unbalanced line driver applications
without changing the circuit gain of 1. Other circuit gains can
be set according to the equation in the diagram. This allows the
design to be easily set for noninverting, inverting, or differential
operation.
R1
2kΩ
VIN 3
6
2 A1
R2
2kΩ
R3
2kΩ
2
3 A2
6
R7
2kΩ
R4
2kΩ
R9
50Ω
R5
2kΩ R6
2kΩ
2
3 A3
6
R8
2kΩ
R10
50Ω
VO1
R11
1kΩ
P1
10kΩ
VO2 – VO1 = VIN
R12
1kΩ
VO2
A1, A2, A3 = OP176
GAIN = R3
R1
SET R2, R4, R5 = R1 AND R6, R7, R8 = R3
Figure 38. A High Speed, Low Noise Differential Line
Driver
REV. 0
–11–
11 Page |
Páginas | Total 21 Páginas | |
PDF Descargar | [ Datasheet OP176.PDF ] |
Número de pieza | Descripción | Fabricantes |
OP176 | Bipolar/JFET / Audio Operational Amplifier | Analog Devices |
OP177 | Ultraprecision Operational Amplifier | Analog Devices |
OP179 | Rail-to-Rail High Output Current Operational Amplifiers | Analog Devices |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |