PDF MM88C30N Data sheet ( Hoja de datos )

Número de pieza MM88C30N
Descripción Quad Single-Ended Line Driver . Dual Differential Line Driver
Fabricantes Fairchild 
Logotipo Fairchild Logotipo

Hay una vista previa y un enlace de descarga de MM88C30N (archivo pdf) en la parte inferior de esta página.

Total 8 Páginas

No Preview Available ! MM88C30N Hoja de datos, Descripción, Manual

October 1987
Revised January 1999
MM88C29 • MM88C30
Quad Single-Ended Line Driver •
Dual Differential Line Driver
General Description
The MM88C30 is a dual differential line driver that also per-
forms the dual four-input NAND or dual four-input AND
function. The absence of a clamp diode to VCC in the input
protection circuitry of the MM88C30 allows a CMOS user to
interface systems operating at different voltage levels.
Thus, a CMOS digital signal source can operate at a VCC
voltage greater than the VCC voltage of the MM88C30 line
driver. The differential output of the MM88C30 eliminates
ground-loop errors.
The MM88C29 is a non-inverting single-wire transmission
line driver. Since the output ON resistance is a low 20
typ., the device can be used to drive lamps, relays, sole-
noids, and clock lines, besides driving data lines.
s Wide supply voltage range: 3V to 15V
s High noise immunity: 0.45 VCC (typ.)
s Low output ON resistance: 20(typ.)
Ordering Code:
Order Number Package Number
Package Description
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Devices also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code.
Connection Diagrams
Pin Assignments for DIP
Pin Assignments for DIP and SOIC
Top View
© 1999 Fairchild Semiconductor Corporation DS005908.prf
Top View

1 page

MM88C30N pdf
Typical Applications
Digital Data Transmission
Note A: Exact value depends on line length.
Note B: Optional to control response time.
Note C: VCC= 4.5V to 5.5V for the DS7820, VCC=4.5V to 15V for the DS78C20.
VCC is 3V to 15V.
Typical Data Rate vs Transmission Line Length
Note: The transmission line used was #22 gauge unshielded twisted pair
(40k termination).
Note: The curves generated assume that both drivers are driving equal
lines, and that the maximum power is 500 mW/package.

5 Page

PáginasTotal 8 Páginas
PDF Descargar[ Datasheet MM88C30N.PDF ]

Hoja de datos destacado

Número de piezaDescripciónFabricantes
MM88C30MM78/78C29 Quad Single-End Line Drvr MM78/88C30 Dual Diff Line Drvr (Rev. A)Texas Instruments
Texas Instruments
MM88C30Dual Differential Line Driver / Quad Single-Ended Line DriverFairchild
MM88C30Dual Differential Line DriverNational
MM88C30JQuad Single-Ended / Dual Differential Line DriverNational

Número de piezaDescripciónFabricantes

High Voltage 3 phase Motor Driver IC.


12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.    |   2020   |  Privacy Policy  |  Contacto  |  Buscar