DataSheet.es    


PDF M34A08-VDW6T Data sheet ( Hoja de datos )

Número de pieza M34A08-VDW6T
Descripción 2 Kbit Serial SMBus EEPROM for ACR Card Configuration
Fabricantes ST Microelectronics 
Logotipo ST Microelectronics Logotipo



Hay una vista previa y un enlace de descarga de M34A08-VDW6T (archivo pdf) en la parte inferior de esta página.


Total 15 Páginas

No Preview Available ! M34A08-VDW6T Hoja de datos, Descripción, Manual

M34A02
2 Kbit Serial SMBus EEPROM for ACR Card Configuration
PRODUCT PREVIEW
s Two Wire SMBus Serial Interface
s 2.7V to 3.6V Single Supply Voltage
s Hardware Write Control
s BYTE and PAGE WRITE (up to 16 Bytes)
s RANDOM and SEQUENTIAL READ Modes
s Self-Timed Programming Cycle
s Automatic Address Incrementing
s Enhanced ESD/Latch-Up Behavior
s More than 1 Million Erase/Write Cycles
s More than 40 Year Data Retention
DESCRIPTION
These electrically erasable programmable
memory (EEPROM) devices are organized as
256x8 bits, and operate down to 2.7 V.
These devices are available in Plastic Small
Outline and Thin Shrink Small Outline packages.
These devices are written by the ACR card-issuer,
and then accessed in Read mode in the
application, using the ACR Serial Bus protocol.
This is a two wire serial interface that uses a bi-
directional data bus and serial clock. The device
carries a built-in 4-bit Device Type Identifier code
(1011).
The device behaves as a slave in the ACR Serial
Bus protocol, with all memory operations
synchronized by the serial clock. Read and Write
operations are initiated by a Start condition,
generated by the bus master. The Start condition
Table 1. Signal Names
E0, E1, E2
Chip Enable
SDA
Serial Data
SCL
Serial Clock
WC Write Control
VCC
VSS
Supply Voltage
Ground
8
1
SO8 (MN)
150 mil width
8
1
TSSOP8 (DW)
169 mil width
Figure 1. Logic Diagram
VCC
3
E0-E2
SCL
WC
M34A02
VSS
SDA
AI03794
April 2001
This is preliminary information on a new product now in development. Details are subject to change without notice.
1/15

1 page




M34A08-VDW6T pdf
M34A02
Table 4. Operating Modes
Mode
RW bit
Current Address Read
1
Random Address Read
0
1
Sequential Read
1
Byte Write
0
Page Write
Note: 1. X = VIH or VIL.
0
WC 1
X
X
X
X
VIL
VIL
same as the pattern applied on Chip Enable (E0,
E1, E2).
The 8th bit is the Read/Write bit (RW). This bit is
set to 1 for Read and 0 for Write operations. If a
match occurs on the Device Select code, the
corresponding device gives an acknowledgment
Bytes
1
1
1
1
16
Initial Sequence
START, Device Select, RW = 1
START, Device Select, RW = 0, Address
reSTART, Device Select, RW = 1
Similar to Current or Random Address Read
START, Device Select, RW = 0
START, Device Select, RW = 0
on Serial Data (SDA) during the 9th bit time. If the
device does not match the Device Select code, it
deselects itself from the bus, and goes into Stand-
by mode.
Figure 6. Write Mode Sequences with WC=1 (data write inhibited)
WC
Byte Write
ACK
ACK
NO ACK
DEV SEL
BYTE ADDR
DATA IN
R/W
WC
Page Write
WC (cont'd)
Page Write
(cont'd)
ACK
ACK
NO ACK
NO ACK
DEV SEL
BYTE ADDR DATA IN 1
DATA IN 2
DATA IN 3
R/W
NO ACK
NO ACK
DATA IN N
AI02803C
5/15

5 Page





M34A08-VDW6T arduino
Table 8. Ordering Information Scheme
Example:
M34A02
–V
DW 6
T
M34A02
Memory Capacity
02 2 Kbit (256 x 8)
Operating Voltage
V 2.7 V to 3.6 V
Package
MN SO8 (150 mil width)
DW TSSOP8 (169 mil width)
Option
T Tape and Reel Packing
Temperature Range
6 –40 °C to 85 °C
output, and sends additional clock pulses so that
the device continues to output the next byte in
sequence. To terminate the stream of bytes, the
bus master must not acknowledge the last byte,
and must generate a Stop condition, as shown in
Figure 8.
The output data comes from consecutive
addresses, with the internal address counter
automatically incremented after each byte output.
After the last memory address, the address
counter ‘rolls-over’, and the device continues to
output data from memory address 00h.
Acknowledge in Read Mode
For all Read commands, the device waits, after
each byte read, for an acknowledgment during the
9th bit time. If the bus master does not drive Serial
Data (SDA) Low during this time, the device
terminates the data transfer and switches to its
Stand-by mode.
The notation used for the device number is as
shown in Table 8. For a list of available options
(speed, package, etc.) or for further information on
any aspect of this device, please contact your
nearest ST Sales Office.
ORDERING INFORMATION
Devices are shipped from the factory with the
memory content set at all 1s (FFh).
11/15

11 Page







PáginasTotal 15 Páginas
PDF Descargar[ Datasheet M34A08-VDW6T.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
M34A08-VDW6T2 Kbit Serial SMBus EEPROM for ACR Card ConfigurationST Microelectronics
ST Microelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar