DataSheet.es    


PDF M29W640DT90N6T Data sheet ( Hoja de datos )

Número de pieza M29W640DT90N6T
Descripción 64 Mbit 8Mb x8 or 4Mb x16 / Boot Block 3V Supply Flash Memory
Fabricantes ST Microelectronics 
Logotipo ST Microelectronics Logotipo



Hay una vista previa y un enlace de descarga de M29W640DT90N6T (archivo pdf) en la parte inferior de esta página.


Total 50 Páginas

No Preview Available ! M29W640DT90N6T Hoja de datos, Descripción, Manual

M29W640DT
M29W640DB
64 Mbit (8Mb x8 or 4Mb x16, Boot Block)
3V Supply Flash Memory
PRELIMINARY DATA
FEATURES SUMMARY
s SUPPLY VOLTAGE
– VCC = 2.7V to 3.6V for Program, Erase, Read
– VPP =12 V for Fast Program (optional)
s ACCESS TIME: 70, 90 ns
s PROGRAMMING TIME
– 10 µs per Byte/Word typical
– Double Word Programming Option
s 135 MEMORY BLOCKS
– 1 Boot Block and 7 Parameter Blocks,
8 KBytes each (Top or Bottom Location)
– 127 Main Blocks, 64 KBytes each
s PROGRAM/ERASE CONTROLLER
– Embedded Byte/Word Program algorithms
s ERASE SUSPEND and RESUME MODES
– Read and Program another Block during
Erase Suspend
s UNLOCK BYPASS PROGRAM COMMAND
– Faster Production/Batch Programming
s VPP/WP Pin for FAST PROGRAM and WRITE
PROTECT
s TEMPORARY BLOCK UNPROTECTION
MODE
s COMMON FLASH INTERFACE
– 64-bit Security Code
s EXTENDED MEMORY BLOCK
– Extra block used as security block or to store
additional information
s LOW POWER CONSUMPTION
– Standby and Automatic Standby
s 100,000 PROGRAM/ERASE CYCLES per
BLOCK
s ELECTRONIC SIGNATURE
– Manufacturer Code: 0020h
– Top Device Code M29W640DT: 22DEh
– Bottom Device Code M29W640DB: 22DFh
Figure 1. Packages
TSOP48 (N)
12 x 20mm
FBGA
TFBGA63 (ZA)
63 ball array
April 2003
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
1/50

1 page




M29W640DT90N6T pdf
M29W640DT, M29W640DB
SUMMARY DESCRIPTION
The M29W640D is a 64 Mbit (8Mb x8 or 4Mb x16)
non-volatile memory that can be read, erased and
reprogrammed. These operations can be per-
formed using a single low voltage (2.7 to 3.6V)
supply. On power-up the memory defaults to its
Read mode where it can be read in the same way
as a ROM or EPROM.
The memory is divided into blocks that can be
erased independently so it is possible to preserve
valid data while old data is erased. Blocks can be
protected in units of 256 KByte (generally groups
of four 64 KByte blocks), to prevent accidental
Program or Erase commands from modifying the
memory. Program and Erase commands are writ-
ten to the Command Interface of the memory. An
on-chip Program/Erase Controller simplifies the
process of programming or erasing the memory by
taking care of all of the special operations that are
required to update the memory contents. The end
of a program or erase operation can be detected
and any error conditions identified. The command
set required to control the memory is consistent
with JEDEC standards.
The device features an asymmetrical blocked ar-
chitecture. The device has an array of 135 blocks:
s 8 Parameters Blocks of 8 KBytes each (or
4 KWords each)
s 127 Main Blocks of 64 KBytes each (or
32 KWords each)
M29W640DT has the Parameter Blocks at the top
of the memory address space while the
M29W640DB locates the Parameter Blocks start-
ing from the bottom.
The M29W640D has an extra block, the Extended
Block, (of 32 KWords in x16 mode or of 64 KBytes
in x8 mode) that can be accessed using a dedicat-
ed command. The Extended Block can be protect-
ed and so is useful for storing security information.
However the protection is not reversible, once pro-
tected the protection cannot be undone.
Chip Enable, Output Enable and Write Enable sig-
nals control the bus operation of the memory.
They allow simple connection to most micropro-
cessors, often without additional logic.
The VPP/WP signal is used to enable faster pro-
gramming of the device, enabling double word
programming. If this signal is held at VSS, the boot
block, and its adjacent parameter block, are pro-
tected from program and erase operations.
The memory is delivered with all the bits erased (set
to 1).
Figure 2. Logic Diagram
VCC VPP/WP
22
A0-A21
15
DQ0-DQ14
W DQ15A–1
M29W640DT
E M29W640DB BYTE
G RB
RP
VSS
AI05733
Table 1. Signal Names
A0-A21
Address Inputs
DQ0-DQ7 Data Inputs/Outputs
DQ8-DQ14 Data Inputs/Outputs
DQ15A–1
(or DQ15)
Data Input/Output or Address Input
(or Data Input/Output)
E Chip Enable
G Output Enable
W Write Enable
RP Reset/Block Temporary Unprotect
RB Ready/Busy Output
BYTE
Byte/Word Organization Select
VCC Supply Voltage
VPP/WP
Supply Voltage for Fast Program
(optional) or Write Protect
VSS Ground
NC Not Connected Internally
5/50

5 Page





M29W640DT90N6T arduino
M29W640DT, M29W640DB
Table 2. Bus Operations, BYTE = VIL
Operation
E GW
Bus Read
VIL VIL VIH
Bus Write
VIL VIH VIL
Output Disable
X VIH VIH
Standby
VIH X
X
Read Manufacturer
Code
VIL
VIL
VIH
Read Device Code
VIL VIL VIH
Extended Memory
Block Verify Code
VIL VIL VIH
Note: X = VIL or VIH.
Address Inputs
DQ15A–1, A0-A21
Cell Address
Command Address
X
X
A0 = VIL, A1 = VIL, A9 = VID,
Others VIL or VIH
A0 = VIH, A1 = VIL,
A9 = VID, Others VIL or VIH
A0 = VIH, A1 = VIH, A6 = VIL,
A9 = VID, Others VIL or VIH
Data Inputs/Outputs
DQ14-DQ8
DQ7-DQ0
Hi-Z Data Output
Hi-Z Data Input
Hi-Z Hi-Z
Hi-Z Hi-Z
Hi-Z 20h
Hi-Z
DEh (M29W640DT)
DFh (M29W640DB)
M29W640DT
98h (factory locked)
18h (not factory locked)
Hi-Z
M29W640DB
88h (factory locked)
08h (not factory locked)
Table 3. Bus Operations, BYTE = VIH
Operation
E GW
Bus Read
VIL VIL VIH
Bus Write
VIL VIH VIL
Output Disable
X VIH VIH
Standby
VIH X
X
Read Manufacturer
Code
VIL
VIL
VIH
Read Device Code
VIL VIL VIH
Address Inputs
A0-A21
Cell Address
Command Address
X
X
A0 = VIL, A1 = VIL, A9 = VID,
Others VIL or VIH
A0 = VIH, A1 = VIL, A9 = VID,
Others VIL or VIH
Extended Memory
Block Verify Code
VIL
VIL
VIH
A0 = VIH, A1 = VIH, A6 = VIL,
A9 = VID, Others VIL or VIH
Note: X = VIL or VIH.
Data Inputs/Outputs
DQ15A–1, DQ14-DQ0
Data Output
Data Input
Hi-Z
Hi-Z
0020h
22DEh (M29W640DT)
22DFh (M29W640DB)
M29W640DT
98h (factory locked)
18h (not factory locked)
M29W640DB
88h (factory locked)
08h (not factory locked)
11/50

11 Page







PáginasTotal 50 Páginas
PDF Descargar[ Datasheet M29W640DT90N6T.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
M29W640DT90N6E64 Mbit 8Mb x8 or 4Mb x16 / Boot Block 3V Supply Flash MemoryST Microelectronics
ST Microelectronics
M29W640DT90N6F64 Mbit 8Mb x8 or 4Mb x16 / Boot Block 3V Supply Flash MemoryST Microelectronics
ST Microelectronics
M29W640DT90N6T64 Mbit 8Mb x8 or 4Mb x16 / Boot Block 3V Supply Flash MemoryST Microelectronics
ST Microelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar