|
|
PDF M66013FP Data sheet ( Hoja de datos )
| Número de pieza | M66013FP | |
| Descripción | 8-BIT I/O EXPANDER WITH ADDRESS | |
| Fabricantes | Mitsubishi | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M66013FP (archivo pdf) en la parte inferior de esta página. Total 2 Páginas | ||
|
No Preview Available !
PRELIMINARYNotice:
Some
pTahriasmisentroict
alimfinitsalasrpeescuifbicjeactitotno.
change.
MITSUBISHI <DIGITAL ASSP>
M66013FP
8-BIT I/O EXPANDER WITH ADDRESS
DESCRIPTION
The M66013FP is a semiconductor IC that is capable of performing
serial-parallel conversion of data. This IC can set addresses.
The microcomputer uses the four signal lines of EN, CLK, DI and
DO to send and receive data.
The IC adopts the two types of operation modes: echo-back mode
and normal mode. In the echo-back mode, data received in serial
can be sent to the sender within the same sequence (*1) as it is.
In the normal mode, restriction is given to the data to be sent to the
sender. However, the normal mode supports the same communi-
cation protocol as that of the M66009FP. (*1): one of the higher
order command bits is excluded.
Three bits in the echo-back mode and four bits in the normal mode
are available for addresses. The echo-back mode and the normal
mode have 8 types and 16 types of address, respectively, and any
address can be set.
Receiving serial data from the microcomputer, the M66013 com-
pares address data included in the data with an address entered in
address setting. Only when these addresses match each other, a
specified command provided are to be executed.
For serial input-parallel output operation, low order 8 bits of the
received 16 bit serial data is converted to parallel data to output to
pins D0 to D7. High order 8 bits are handled as address or com-
mand bits. Since the writing operation to the data register for
parallel output and the outputting operation of register contents to
pins D0 to D7 are performed with different commands and can be
controlled independently, the register contents must be checked
before output of the specified data to pins D0 to D7.
For parallel input-serial output operation, parallel data of pins D0 to
D7 are outputted to low order 8 bits of the sended 16 bit serial
data. The contents of high order 8 bits of the sended 16 bit serial
data differs in the using operation mode.
In echo mode, the I/O port output format is capable of setting to
either N-ch or P-ch open drain. In normal mode, the I/O port output
format is fixed to P-ch open drain.
FEATURES
• Is capable of providing high speed serial communication at 8
MHz.
• Provides two modes: echo back mode and normal mode.
PIN CONFIGURATION (TOP VIEW)
CLOCK INPUT CLK
SERIAL DATA
INPUT
SERIAL DATA
OUTPUT
DATA ENABLE
INPUT
DI
DO
EN
A0
ADDRESS SET
INPUT
A1
A2
ADDRESS
SET/OUTPUT A3
SET INPUT /PNSET
MODE SET INPUT MD
1
2
3
4
5
6
7
8
9
GND 10
20 VCC
19
RESET
RESET
INPUT
18 D7
17 D6
16 D5
15 D4 PARALLEL
DATA
14 D3 INPUT/OUTPUT
13 D2
12 D1
11 D0
Outline 20P2N-A (20 pin SOP)
• Is capable of reading serial input data in echo back mode.
(However, 3 bits are available for the address.)
• Is capable of achieving communication protocol of current
M66009FP in the normal mode. (However, 4 bits are available for
the address.)
• Uses different commands in operations for output of data to I/O
port: command for writing data into an output register and
command for output operation to the I/O port.
• Provides an I/O port data read only command.
• Is capable of reading an output register.
• Adopts a decision by majority by reading three types of data when
serial data is received.
• Is capable of setting the I/O port output format to either N-ch or P-
ch open drain. (In echo mode)
APPLICATIONS
Inter board communication in VTR, AV and OA equipment, expan-
sion of microcomputer I/O port, etc.
BLOCK DIAGRAM
DATA ENABLE
INPUT EN 4
CLOCK INPUT CLK 1
ADDRESS SET INPUT MODE SET INPUT
A0 A1 A2 A3 MD
56 78
9
COMMAND CONTROL
CIRCUIT
ACK BIT, OUTPUT SET FLAG
16
SERIAL DATA INPUT DI 2
SERIAL DATA DO 3
OUTPUT
SELECTOR
RESET INPUT RESET 19
VCC 20
GND 10
SHIFT REGISTER FOR
SERIAL INPUT (16 bits)
16
DATA REGISTER FOR
PARALLEL OUTPUT (16 bits)
8
SHIFT REGISTER FOR
SERIAL OUTPUT (16 bits)
8
11 D0
12 D1
13 D2
14 D3
15 D4
PARALLEL DATA
INPUT/OUTPUT
16 D5
17 D6
18 D7
1
1 page | ||
| Páginas | Total 2 Páginas | |
| PDF Descargar | [ Datasheet M66013FP.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M66013FP | 8-BIT I/O EXPANDER WITH ADDRESS | Mitsubishi |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |