|
|
Número de pieza | M62332P | |
Descripción | 8-BIT 2CH I2C BUS D-A CONVERTER WITH BUFFER AMPLIFIERS | |
Fabricantes | Mitsubishi | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de M62332P (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! MITSUBISHI <STD. LINEAR ICs>
M62332P/FP
M62337P/FP
8-BIT 2CH I2C BUS D-A CONVERTER WITH BUFFER AMPLIFIERS
DESCRIPT ION
The M62332/M62337 is an integrated circuit
semiconductor of CMOS structure with 2 channels of built
in D-A converters with output buffer operational amplifiers.
The input is 2-wires serial method is used for the transfer
format of digital data to allow connection with a
microcomputer with minimum wiring.
The output buffer operational amplifier employs AB class
output circuit with sync and source drive capacity of 1.0mA
or more,and it operates in the whole voltage range from
Vcc to ground.
The M62332 and the M62337 differ only in their slave
address.
PIN CONFIGURATION(TOP VIEW)
Ao1 1
Ao2 2
N.C. 3
N.C. 4
8 Vcc
7 SCL
6 SDA
5 GND
Outline 8P4 (P)
8P2S-A (FP)
FEATUR ES
• Digital data transfer format
I2C BUS serial data method
• Output buffer operational amplifier
it operates in the whole voltage range from Vcc to
ground.
• High output current drive capacity
±1.0mA over
N.C.:NO CONNECTION
APPLIC ATION
Conversion from digital data to analog control data for
home-use and industrial equipment.
Signal gain control or automatic adjustment of DISPLAY-
MONITOR or CTV.
BLOCK DIAGRAM
Vcc
8
SCL
7
SDA
6
GND
5
POWER ON
RESET
I2C BUS TRANSCEIVER
CHANNEL
DECODER
8
8bit Latch
8bit upper
segment R-2R
8bit Latch
8bit upper
segment R-2R
12
Ao1 Ao2
MITSUBISHI ELECTRIC
980714 rev.F (1 / 6 )
1 page MITSUBISHI <STD. LINEAR ICs>
M62332P/FP
M62337P/FP
8-BIT 2CH I2C BUS D-A CONVERTER WITH BUFFER AMPLIFIERS
TIMING CHART (MODEL)
•start condition to slave address bite
SDA
1 2 3 4 5 6 7W A
SCL
D/A
output
start condition
•sub address bite
SDA
1 2 34 5 6 7 8 A
SCL
D/A
output
•DAC data bite to stop condition
SDA
1 23 4 5 6 7 8 A
SCL
D/A
output
stop condition
•Start condition
With SCL at HIGH,SDA line goes from HIGH to LOW
•Stop condition
With SCL at HIGH,SDA line goes from LOW to HIGH
(Under normal circumstances,SDA is changed when SCL is LOW)
•Acknowledge bit
The receiving IC has to pull down SDA line whenever receive slave data.
(The transmitting IC releases the SDA line just then transmit 8bit data.)
Digital Data Formats
STA SLAVE ADDRESS
W A SUB ADDRESS 1 A DAC DATA 1 A
SUB ADDRESS 2 A DAC DATA 2 A
SUB ADDRESS n A DAC DATA n A STP
MITSUBISHI ELECTRIC
980714 rev.F ( 5 / 6 )
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet M62332P.PDF ] |
Número de pieza | Descripción | Fabricantes |
M62332FP | 8-BIT 2CH I2C BUS D-A CONVERTER WITH BUFFER AMPLIFIERS | Mitsubishi |
M62332FP | 8-bit 2ch I2C BUS D/A Converter | Renesas |
M62332P | 8-BIT 2CH I2C BUS D-A CONVERTER WITH BUFFER AMPLIFIERS | Mitsubishi |
M62332P | 8-bit 2ch I2C BUS D/A Converter | Renesas |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |