DataSheet.es    


PDF M58LW64D Data sheet ( Hoja de datos )

Número de pieza M58LW64D
Descripción 64 Mbit (8Mb x8 / 4Mb x16 / Uniform Block) 3V Supply Flash Memory
Fabricantes ST Microelectronics 
Logotipo ST Microelectronics Logotipo



Hay una vista previa y un enlace de descarga de M58LW64D (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! M58LW64D Hoja de datos, Descripción, Manual

M58LW064D
64 Mbit (8Mb x8, 4Mb x16, Uniform Block)
3V Supply Flash Memory
FEATURES SUMMARY
WIDE x8 or x16 DATA BUS for HIGH
BANDWIDTH
SUPPLY VOLTAGE
– VDD = VDDQ = 2.7 to 3.6V for Program,
Erase and Read operations
ACCESS TIME
– Random Read 110ns
– Page Mode Read 110/25ns
PROGRAMMING TIME
– 16 Word Write Buffer
– 12µs Word effective programming time
64 UNIFORM 64 KWord/128KByte MEMORY
BLOCKS
ENHANCED SECURITY
– Block Protection/ Unprotection
– VPEN signal for Program Erase Enable
– 128 bit Protection Register with 64 bit
Unique Code in OTP area
PROGRAM and ERASE SUSPEND
COMMON FLASH INTERFACE
100, 000 PROGRAM/ERASE CYCLES per
BLOCK
ELECTRONIC SIGNATURE
– Manufacturer Code: 0020h
– Device Code M58LW064D: 0017h
PACKAGES
– Compliant with Lead-Free Soldering
Processes
– Lead-Free Versions
Figure 1. Packages
TSOP56 (N)
14 x 20 mm
TBGA
TBGA64 (ZA)
10 x 13 mm
September 2004
1/50

1 page




M58LW64D pdf
M58LW064D
SUMMARY DESCRIPTION
The M58LW064D is a 64 Mbit (8Mb x 8 or 4Mb
x16) non-volatile memory that can be read, erased
and reprogrammed. These operations can be per-
formed using a single low voltage (2.7V to 3.6V)
core supply.
The memory is divided into 64 blocks of 1Mbit that
can be erased independently so it is possible to
preserve valid data while old data is erased. Pro-
gram and Erase commands are written to the
Command Interface of the memory. An on-chip
Program/Erase Controller simplifies the process of
programming or erasing the memory by taking
care of all of the special operations that are re-
quired to update the memory contents. The end of
a Program or Erase operation can be detected and
any error conditions identified in the Status Regis-
ter. The command set required to control the
memory is consistent with JEDEC standards.
The Write Buffer allows the microprocessor to pro-
gram from 1 to 16 Words in parallel, both speeding
up the programming and freeing up the micropro-
cessor to perform other work. A Word Program
command is available to program a single word.
Erase can be suspended in order to perform either
Read or Program in any other block and then re-
sumed. Program can be suspended to Read data
in any other block and then resumed. Each block
can be programmed and erased over 100,000 cy-
cles.
The M58LW064D has several security features to
increase data protection.
Block Protection, where each block can be
individually protected against program or
erase operations. All blocks are protected
during power-up. The protection of the blocks
is non-volatile; after power-up the protection
status of each block is restored to the state
when power was last removed.
Program Erase Enable input VPEN, program or
erase operations are not possible when the
Program Erase Enable input VPEN is low.
128 bit Protection Register, divided into two 64
bit segments: the first contains a unique
device number written by ST, the second is
user programmable. The user programmable
segment can be protected.
The Reset/Power-Down pin is used to apply a
Hardware Reset to the enabled memory and to set
the device in power-down mode.
The device features an Auto Low Power mode. If
the bus becomes inactive during read operations,
the device automatically enters Auto Low Power
mode. In this mode the power consumption is re-
duced to the Auto Low Power supply current.
The STS signal is an open drain output that can be
used to identify the Program/Erase Controller sta-
tus. It can be configured in two modes: Ready/
Busy mode where a static signal indicates the sta-
tus of the P/E.C, and Status mode where a pulsing
signal indicates the end of a Program or Block
Erase operation. In Status mode it can be used as
a system interrupt signal, useful for saving CPU
time.
The memory is available in TSOP56 (14 x 20 mm)
and TBGA64 (10x13mm, 1mm pitch) packages.
In addition to the standard version, the packages
are also available in Lead-free version, in compli-
ance with JEDEC Std J-STD-020B, the ST ECO-
PACK 7191395 Specification, and the RoHS
(Restriction of Hazardous Substances) directive.
All packages are compliant with Lead-free solder-
ing processes.
5/50

5 Page





M58LW64D arduino
M58LW064D
When the Program/Erase Controller is idle, or sus-
pended, STS can float High through a pull-up re-
sistor. The use of an open-drain output allows the
STS pins from several memories to be connected
to a single pull-up resistor (a Low will indicate that
one, or more, of the memories is busy).
STS is not Low during a reset unless the reset was
applied when the Program/Erase controller was
active
Program/Erase Enable (VPEN). The Program/
Erase Enable input, VPEN, is used to protect all
blocks, preventing Program and Erase operations
from affecting their data.
Program/Erase Enable must be kept High during
all Program/Erase Controller operations, other-
wise the operations is not guaranteed to succeed
and data may become corrupt.
VDD Supply Voltage. VDD provides the power
supply to the internal core of the memory device.
It is the main power supply for all operations
(Read, Program and Erase).
VDDQ Supply Voltage. VDDQ provides the power
supply to the I/O pins and enables all Outputs to
be powered independently from VDD. VDDQ can be
tied to VDD or can use a separate supply.
It is recommended to power-up and power-down
VDD and VDDQ together to avoid any condition that
would result in data corruption.
VSS Ground. Ground, VSS, is the reference for
the core power supply. It must be connected to the
system ground.
VSSQ Ground. VSSQ ground is the reference for
the input/output circuitry driven by VDDQ. VSSQ
must be connected to VSS.
Note: Each device in a system should have
VDD and VDDQ decoupled with a 0.1µF ceramic
capacitor close to the pin (high frequency, in-
herently low inductance capacitors should be
as close as possible to the package). See Fig-
ure 8., AC Measurement Load Circuit.
Table 2. Device Enable
E2 E1
VIL VIL
VIL VIL
VIL VIH
VIL VIH
VIH VIL
VIH VIL
VIH VIH
VIH VIH
Note: For single device operations, E2 and E1 can be connected to VSS.
E0
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
Device
Enabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Disabled
11/50

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet M58LW64D.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
M58LW64D64 Mbit (8Mb x8 / 4Mb x16 / Uniform Block) 3V Supply Flash MemoryST Microelectronics
ST Microelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar