DataSheet.es    


PDF M29W160BT Data sheet ( Hoja de datos )

Número de pieza M29W160BT
Descripción 16 Mbit 2Mb x8 or 1Mb x16 / Boot Block Low Voltage Single Supply Flash Memory
Fabricantes ST Microelectronics 
Logotipo ST Microelectronics Logotipo



Hay una vista previa y un enlace de descarga de M29W160BT (archivo pdf) en la parte inferior de esta página.


Total 25 Páginas

No Preview Available ! M29W160BT Hoja de datos, Descripción, Manual

M29W160BT
M29W160BB
16 Mbit (2Mb x8 or 1Mb x16, Boot Block)
Low Voltage Single Supply Flash Memory
PRELIMINARY DATA
s SINGLE 2.7 to 3.6V SUPPLY VOLTAGE for
PROGRAM, ERASE and READ OPERATIONS
s ACCESS TIME: 70ns
s PROGRAMMING TIME
– 10µs per Byte/Word typical
s 35 MEMORY BLOCKS
– 1 Boot Block (Top or Bottom Location)
– 2 Parameter and 32 Main Blocks
s PROGRAM/ERASE CONTROLLER
– Embedded Byte/Word Program algorithm
– Embedded Multi-Block/Chip Erase algorithm
– Status Register Polling and Toggle Bits
– Ready/Busy Output Pin
s ERASE SUSPEND and RESUME MODES
– Read and Program another Block during
Erase Suspend
s UNLOCK BYPASS PROGRAM COMMAND
– Faster Production/Batch Programming
s TEMPORARY BLOCK UNPROTECTION
MODE
s SECURITY MEMORY BLOCK
s LOW POWER CONSUMPTION
– Standby and Automatic Standby
s 100,000 PROGRAM/ERASE CYCLES per
BLOCK
s 20 YEARS DATA RETENTION
– Defectivity below 1 ppm/year
s ELECTRONIC SIGNATURE
– Manufacturer Code: 0020h
– Top Device Code M29W160BT: 22C4h
– Bottom Device Code M29W160BB: 2249h
44
TSOP48 (N)
12 x 20mm
1
SO44 (M)
FBGA
LFBGA48 (ZA)
8 x 6 solder balls
Figure 1. Logic Diagram
VCC
20
A0-A19
15
DQ0-DQ14
W DQ15A–1
M29W160BT
E M29W160BB BYTE
G RB
RP
VSS
AI00981
Note: RB not available on SO44 package.
February 2000
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
1/25

1 page




M29W160BT pdf
Table 3. Top Boot Block Addresses,
M29W160BT
#
Size
(Kbytes)
Address Range
(x8)
Address Range
(x16)
34 16 1FC000h-1FFFFFh FE000h-FFFFF h
33 8 1FA000h-1FBFFFh FD000h-FDFFFh
32 8 1F8000h-1F9FFFh FC000h-FCFFFh
31 32 1F0000h-1F7FFFh F8000h-FBFFFh
30 64 1E0000h-1EFFFFh F0000h-F7FFFh
29 64 1D0000h-1DFFFFh E8000h-EFFFFh
28 64 1C0000h-1CFFFFh E0000h-E7FFFh
27 64 1B0000h-1BFFFFh D8000h-DFFFFh
26 64 1A0000h-1AFFFFh D0000h-D7FFFh
25 64 190000h-19FFFFh C8000h-CFFFFh
24 64 180000h-18FFFFh C0000h-C7FFFh
23 64 170000h-17FFFFh B8000h-BFFFFh
22 64 160000h-16FFFFh B0000h-B7FFFh
21 64 150000h-15FFFFh A8000h-AFFFFh
20 64 140000h-14FFFFh A0000h-A7FFFh
19 64 130000h-13FFFFh 98000h-9FFFFh
18 64 120000h-12FFFFh 90000h-97FFFh
17 64 110000h-11FFFFh 88000h-8FFFFh
16 64 100000h-10FFFFh 80000h-87FFFh
15 64 0F0000h-0FFFFFh 78000h-7FFFFh
14 64 0E0000h-0EFFFFh 70000h-77FFFh
13 64 0D0000h-0DFFFFh 68000h-6FFFFh
12 64 0C0000h-0CFFFFh 60000h-67FFFh
11 64 0B0000h-0BFFFFh 58000h-5FFFFh
10 64 0A0000h-0AFFFFh 50000h-57FFFh
9 64 090000h-09FFFFh 48000h-4FFFFh
8 64 080000h-08FFFFh 40000h-47FFFh
7 64 070000h-07FFFFh 38000h-3FFFFh
6 64 060000h-06FFFFh 30000h-37FFFh
5 64 050000h-05FFFFh 28000h-2FFFFh
4 64 040000h-04FFFFh 20000h-27FFFh
3 64 030000h-03FFFFh 18000h-1FFFFh
2 64 020000h-02FFFFh 10000h-17FFFh
1 64 010000h-01FFFFh 08000h-0FFFFh
0 64 000000h-00FFFFh 00000h-07FFFh
M29W160BT, M29W160BB
Table 4. Bottom Boot Block Addresses,
M29W160BB
#
Size
(Kbytes)
Address Range
(x8)
Address Range
(x16)
34 64 1F0000h-1FFFFFh F8000h-FFFFFh
33 64 1E0000h-1EFFFFh F0000h-F7FFFh
32 64 1D0000h-1DFFFFh E8000h-EFFFFh
31 64 1C0000h-1CFFFFh E0000h-E7FFFh
30 64 1B0000h-1BFFFFh D8000h-DFFFF h
29 64 1A0000h-1AFFFFh D0000h-D7FFFh
28 64 190000h-19FFFFh C8000h-CFFFF h
27 64 180000h-18FFFFh C0000h-C7FFFh
26 64 170000h-17FFFFh B8000h-BFFFFh
25 64 160000h-16FFFFh B0000h-B7FFFh
24 64 150000h-15FFFFh A8000h-AFFFFh
23 64 140000h-14FFFFh A0000h-A7FFFh
22 64 130000h-13FFFFh 98000h-9FFFF h
21 64 120000h-12FFFFh 90000h-97FFFh
20 64 110000h-11FFFFh 88000h-8FFFF h
19 64 100000h-10FFFFh 80000h-87FFFh
18 64 0F0000h-0FFFFFh 78000h-7FFFF h
17 64 0E0000h-0EFFFFh 70000h-77FFFh
16 64 0D0000h-0DFFFFh 68000h-6FFFF h
15 64 0C0000h-0CFFFFh 60000h-67FFFh
14 64 0B0000h-0BFFFFh 58000h-5FFFF h
13 64 0A0000h-0AFFFFh 50000h-57FFFh
12 64 090000h-09FFFFh 48000h-4FFFF h
11 64 080000h-08FFFFh 40000h-47FFFh
10 64 070000h-07FFFFh 38000h-3FFFF h
9 64 060000h-06FFFFh 30000h-37FFFh
8 64 050000h-05FFFFh 28000h-2FFFF h
7 64 040000h-04FFFFh 20000h-27FFFh
6 64 030000h-03FFFFh 18000h-1FFFF h
5 64 020000h-02FFFFh 10000h-17FFFh
4 64 010000h-01FFFFh 08000h-0FFFF h
3 32 008000h-00FFFFh 04000h-07FFFh
2 8 006000h-007FFFh 03000h-03FFFh
1 8 004000h-005FFFh 02000h-02FFFh
0 16 000000h-003FFFh 00000h-01FFFh
5/25

5 Page





M29W160BT arduino
M29W160BT, M29W160BB
Erase Suspend Command. The Erase Suspend
Command may be used to temporarily suspend a
Block Erase operation and return the memory to
Read mode. The command requires one Bus
Write operation.
The Program/Erase Controller will suspend within
15µs of the Erase Suspend Command being is-
sued. Once the Program/Erase Controller has
stopped the memory will be set to Read mode and
the Erase will be suspended. If the Erase Suspend
command is issued during the period when the
memory is waiting for an additional block (before
the Program/Erase Controller starts) then the
Erase is suspended immediately and will start im-
mediately when the Erase Resume Command is
issued. It will not be possible to select any further
blocks for erasure after the Erase Resume.
During Erase Suspend it is possible to Read and
Program cells in blocks that are not being erased;
both Read and Program operations behave as
normal on these blocks. Reading from blocks that
are being erased will output the Status Register. It
is also possible to enter the Auto Select mode: the
memory will behave as in the Auto Select mode on
all blocks until a Read/Reset command returns the
memory to Erase Suspend mode.
Erase Resume Command. The Erase Resume
command must be used to restart the Program/
Erase Controller from Erase Suspend. An erase
can be suspended and resumed more than once.
Security Data Command. The Security Data
command can be used to read the Security Mem-
ory Block. The Security Memory Block is a block of
256 words that is usually undefined. Volume cus-
tomers can request that a unique security code is
pre-programmed by ST into each part. One Bus
Write operation is required to issue the Security
Data command. Once the Security Data command
is issued Bus Read operations read from the Se-
curity Memory Block instead of the memory array,
until another command is issued.
After issuing the Security Data command from
Auto Select mode a Read/Reset command will re-
turn to Auto Select mode. An invalid command will
return to Read mode.
Valid addresses for the Security Memory Block are
given in Table 9, Security Memory Block Address-
es. Although the address for the Security Data
command is Don’t Care, it is necessary to choose
an address outside the Security Memory Block for
correct operation.
Table 9. Security Memory Block Addresses
Size
(words)
Address Range
(x8)
Address Range
(x16)
256 000000h-0001FFh 000000h-0000FFh
Table 10. Program, Erase Times and Program, Erase Endurance Cycles
(TA = 0 to 70°C or –40 to 85°C)
Parameter
Min
Typ (1)
Typical after
100k W/E Cycles (1)
Chip Erase (All bits in the memory set to ‘0’)
10 10
Chip Erase
22 22
Block Erase (64 Kbytes)
0.8 0.8
Program (Byte or Word)
10 10
Chip Program (Byte by Byte)
22 22
Chip Program (Word by Word)
11 11
Program/Erase Cycles (per Block)
100,000
Note: 1. TA = 25°C, VCC = 3.3V.
Max Unit
sec
120 sec
6 sec
200 µs
120 sec
60 sec
cycles
11/25

11 Page







PáginasTotal 25 Páginas
PDF Descargar[ Datasheet M29W160BT.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
M29W160BB16 Mbit 2Mb x8 or 1Mb x16 / Boot Block Low Voltage Single Supply Flash MemoryST Microelectronics
ST Microelectronics
M29W160BT16 Mbit 2Mb x8 or 1Mb x16 / Boot Block Low Voltage Single Supply Flash MemoryST Microelectronics
ST Microelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar