DataSheet.es    


PDF LCX011AM Data sheet ( Hoja de datos )

Número de pieza LCX011AM
Descripción 3.6cm (1.43-inch) LCD Panel (with microlens)
Fabricantes Sony 
Logotipo Sony Logotipo



Hay una vista previa y un enlace de descarga de LCX011AM (archivo pdf) en la parte inferior de esta página.


Total 23 Páginas

No Preview Available ! LCX011AM Hoja de datos, Descripción, Manual

LCX011AM
3.6cm (1.43-inch) LCD Panel (with microlens)
For the availability of this product, please contact the sales office.
Description
The LCX011AM is a 3.6cm diagonal active matrix
TFT-LCD panel addressed by polycrystalline silicon
super thin film transistors with built-in peripheral
driving circuit. This panel allows full-color representation
without color filters through the use of a microlens.
This panel provides a wide aspect ratio of 16:9,
such as those represented in HD. The built-in side-
black function also allows an aspect ratio of 4:3 in
the NTSC/PAL mode.
This panel has a polysilicon TFT high-speed scanner
and built-in function to display images up/down
and/or right/left inverse. The built-in 5V interface
circuit leads to lower voltage of timing and control
signals.
Features
The number of active dots: 768,000 (1.43-inch; 3.6cm in diagonal)
Horizontal resolution: 600TV lines
Effective aperture ratio: 70% (reference value)
High contrast ratio with normally white mode: 200 (typ.)
Built-in H and V drivers (built-in input level conversion circuit, 5V driving possible)
NTSC/NTSC-WIDE/HD (band: 20MHz) mode selectable
(PAL/PAL-WIDE mode also available through conversion of scanned dot numbers by an external IC)
Up/down and/or right/left inverse display function
Side-black function
16:9 and 4:3 aspect-ratio switching function
Element Structure
Dots
16:9 display: 1599.5 (H) × 480 (V) = 767,760
4:3 display: 1199.5 (H) × 480 (V) = 575,760
Built-in peripheral driver using polycrystalline silicon super thin film transistors.
Applications
Liquid crystal projectors, etc.
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E96919A94-PS

1 page




LCX011AM pdf
LCX011AM
Input Signals
1. Input signal voltage conditions
(Vss = 0V)
Item Symbol Min. Typ. Max. Unit
H driver input voltage
(Low) VHIL
WID, RGT, HST, HCK1, HCK2 (High) VHIH
–0.5
4.5
0.0
5.0
0.3 V
5.5 V
V driver input voltage
ENB, VCK, PCG, VST, DWN
(Low) VVIL
(High) VVIH
–0.5
4.5
0.0
5.0
0.3 V
5.5 V
Video signal center voltage
Video signal input range1 (SIG1 to 6)
Common voltage of panel2
Side black signal for 4:3 display3 (SID)
input voltage
VVC
Vsig
Vcom
Vsid
6.8 7.0 7.2
VVC – 4.5 — VVC + 4.5
VVC – 0.3 VVC – 0.2 VVC – 0.1
VVC ± 4.4 VVC ± 4.5 VVC ± 4.6
(VVC ± 3.1) (VVC ± 3.2) (VVC ± 3.3)
V
V
V
V
1 Video input signal shall be symmetrical to VVC.
2 Common voltage of the panel shall be adjusted to VVC – 0.2V.
3 The side black signal for 4:3 display shall be input at the timing shown in the figure below. Also, the interval
between the SID rise and fall shall be kept to 800ns or less.
4.5V
2.1µs
3.2V
SID
2.1µs
3.2V 4.5V
VVC
PCG
Level Conversion Circuit
The LCX011AM has a built-in level conversion circuit in the clock input unit on the panel. The input signal level
increases to HVDD or VVDD. The VCC of external ICs are applicable to 5 ± 0.5V.
–5–

5 Page





LCX011AM arduino
LCX011AM
<Electro-optical Characteristics Measurement>
Basic measurement conditions
(1) Driving voltage
HVDD = 13.5V, VVDD = 13.5V, AVDD = 15.5V
VVC = 7.0V, Vcom = 6.8V
(2) Measurement temperature
25˚C unless otherwise specified.
(3) Measurement point
One point in the center of screen unless
otherwise specified.
(4) Measurement systems
Two types of measurement system are used
as shown below.
(5) Video input signal voltage (Vsig)
Vsig = 7.0 ± VAC [V] (VAC: signal amplitude)
(6) Optical measurement systems
Measurement system I
Relay lens system
B R G Dichroic mirrors
Elliptic mirror
Fresnel lens
LCD panel
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.0
100W lamp angle distribution
1.0 2.0 3.0 3.5
Panel incident light dispersion angle [ ° ]
4.0
Projection lenses
Screen
Measurement system II
Light receptor lens
Optical fiber
Light Detector
Measurement
Equipment
Drive Circuit
LCD panel
Light
Source
1. Contrast ratio
Contrast Ratio (CR) is given by the following formula (1).
CR = L (White) ...... (1)
L (Black)
L (White): Surface luminance of the TFT-LCD panel at the input signal amplitude VAC = 0.5V.
L (Black): Surface luminance of the panel at VAC = 4.5V.
Both luminosities are measured by System I.
– 11 –

11 Page







PáginasTotal 23 Páginas
PDF Descargar[ Datasheet LCX011AM.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LCX011AM3.6cm (1.43-inch) LCD Panel (with microlens)Sony
Sony

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar