DataSheet.es    


PDF LCDA15 Data sheet ( Hoja de datos )

Número de pieza LCDA15
Descripción Low Capacitance TVS Diode Array For High-Speed Data Interfaces
Fabricantes Semtech 
Logotipo Semtech Logotipo



Hay una vista previa y un enlace de descarga de LCDA15 (archivo pdf) en la parte inferior de esta página.


Total 7 Páginas

No Preview Available ! LCDA15 Hoja de datos, Descripción, Manual

LCDA05 THRU LCDA24
Low Capacitance TVS Diode Array
For High-Speed Data Interfaces
PROTECTION PRODUCTS
Description
Features
The LCDA series of TVS arrays are designed to protect
sensitive electronics from damage or latch-up due to
ESD and other voltage-induced transient events. Each
device will protect two high-speed lines. They are
available with operating voltages of 5V, 12V, 15V and
24V. They are bidirectional devices and may be used on
lines where the signal polarities are above and below
ground.
TVS diodes are solid-state devices designed specifically
for transient suppression. They offer desirable charac-
teristics for board level protection including fast re-
sponse time, low operating and clamping voltage and
no device degradation. The LCDA series devices
feature low capacitance compensation diodes in series
with standard TVS diodes to provide an integrated, low
capacitance solution for use on high-speed interfaces.
The LCDA series devices may be used to meet the
immunity requirements of IEC 61000-4-2, level 4.
u Transient protection for high-speed data lines to
IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
IEC 61000-4-5 (Lightning) 24A (tp = 8/20µs)
u Protects two I/O lines
u Low capacitance for high-speed data lines
u Working voltages: 5V, 12V, 15V and 24V
u Low leakage current
u Low operating and clamping voltages
u Solid-state silicon avalanche technology
Mechanical Characteristics
u JEDEC SO-8 (MS-012AA) small outline package
u Molding compound flammability rating: UL 94V-0
u Marking : Part Number, Logo, Date Code
u Packaging : Tape and Reel per EIA 481
Applications
u High-Speed Data Lines
u Microprocessor Based Equipment
u Universal Serial Bus (USB) Port Protection
u Notebooks, Desktops, & Servers
u Instrumentation
u LAN/WAN Equipment
u Peripherals
Circuit Diagram (Each Line Pair)
Revision 9/2000
Schematic & PIN Configuration
18
27
36
45
SO-8 (Top View)
1 www.semtech.com

1 page




LCDA15 pdf
LCDA05 THRU LCDA24
PROTECTION PRODUCTS
Applications Information
Device Connection for Protection of Two High-Speed
Data Lines
The LCDAxx is designed to protect up to two high-speed
data lines. The LCDAxx utilizes a low capacitance
compensation diode in series with, but in opposite
polarity to a TVS diode in each line. The resulting
capacitance is less than 5pF per line. Each line will
only suppress transient events in one polarity. There-
fore, to achieve protection in both positive and nega-
tive polarity, a second TVS/rectifier pair is connected in
anti-parallel to the first. Pins 1, 2, 7, and 8 are used to
protect one data line. Pins 3, 4, 5, and 6 are used to
protect the second data line.
The device is connected as follows:
l Pins 1 & 2 are tied together and pins 7 & 8 are tied
together providing the protection circuit for one I/O
line. Pins 3 & 4 are tied together and pins 5 & 6
are tied together providing the protection circuit for
the second I/O line. Since the device is electrically
symmetrical, either side of the connected pairs
may be used to protect the lines. The other side of
the pair is used to make the ground connection.
The ground connections should be made directly to
the ground plane for best results. The path length
is kept as short as possible to reduce the effects
of parasitic inductance in the board traces.
Circuit Board Layout Recommendations for Suppres-
sion of ESD.
Good circuit board layout is critical for the suppression
of ESD induced transients. The following guidelines are
recommended:
l Place the TVS near the input terminals or connec-
tors to restrict transient coupling.
l Minimize the path length between the TVS and the
protected line.
l Minimize all conductive loops including power and
ground loops.
l The ESD transient return path to ground should be
kept as short as possible.
l Never run critical signals near board edges.
l Use ground planes whenever possible.
ã 2000 Semtech Corp.
5
LCDA Connection Diagram
I/O 1
I/O 2
1
2
3
4
8
I/O 1
7
6
I/O 2
5
I/O Line Protection
Connection Options
To Protected
Device
Line 1
In/Out
1
2
8
Line 1
Ground
7
3
Line 2
Ground
4
6
Line 2
In/Out
5
Line 1 1
In/Out
2
3
4
From Connector
To Protected
Device
8
Line 2
In/Out
7
Ground
6
5
From Connector
www.semtech.com

5 Page










PáginasTotal 7 Páginas
PDF Descargar[ Datasheet LCDA15.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LCDA12Low Capacitance TVS Diode Array For High-Speed Data InterfacesSemtech
Semtech
LCDA12TVS Array SeriesSMC
SMC
LCDA12C-1Low Capacitance TVS Diode ArraySemtech
Semtech
LCDA12C-1TCLow Capacitance TVS Diode ArraySemtech
Semtech

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar