DataSheet.es    


PDF LA7191N Data sheet ( Hoja de datos )

Número de pieza LA7191N
Descripción Global VHS-format VCR Video Signal Processor
Fabricantes Sanyo 
Logotipo Sanyo Logotipo



Hay una vista previa y un enlace de descarga de LA7191N (archivo pdf) en la parte inferior de esta página.


Total 11 Páginas

No Preview Available ! LA7191N Hoja de datos, Descripción, Manual

Ordering number: EN 5471
Monolithic Linear IC
LA7191N
Global VHS-format VCR
Video Signal Processor
Overview
The LA7191N is a multi-format, single-chip video signal
processing IC that supports TV systems around the world.
.Features
Compatible with TV systems around the world (NTSC/
. PAL/MESECAM/4.43 -NTSC/PAL-M/PAL-N).
All filters on chip, except for PB-LPF for chroma (cutoff
frequency requires no adjustment).
. No adjustment of YNR and DOC levels.
. Double high-pass noise canceller on chip.
. Linear phase-type picture control on chip.
. fsc output can be used as clock for OSD IC.
. DCC circuit on chip.
. Pilot burst erasure circuit on chip.
. High-speed AFC circuit on chip.
. Switching noise canceller on chip.
. Smallest package in the industry.
. Few components needed.
. 2fsc output.
. I/O pin for CNR insertion added.
. YNR/LNC switching possible.
Package Dimensions
unit: mm
3025B-DIP42S
[LA7191N]
SANYO : DIP42S
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Allowable power dissipation
Operating temperature
Storage temperature
Symbol
VCC max
Pd max
Topr
Tstg
Operating Conditions at Ta = 25°C
Parameter
Recommended supply voltage
Operating supply voltage range
Symbol
VCC
VCCop
Conditions
Ta %65°C
Conditions
Ratings
7.0
1020
–10 to +65
–40 to +150
Unit
V
mW
°C
°C
Ratings
5.0
4.8 to 5.5
Unit
V
V
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
22896HA (II) No.5471 - 1/11

1 page




LA7191N pdf
LA7191N
Continued from preceding page.
Parameter
VXO oscillation level
REC ACC characteristics
REC ACC killer input level
REC ACC killer output level
Input level for REC ACC
killer return
VXO control sensitivity
REC APC pull-in range
BGP delay time
Symbol Input Output
Conditions
VVXO-R
T37A T19 VIN = standard color bar signal (1 Vp-p),
measure T19 output amplitude (with a FET
probe)
ACCR1
ACCR2
VACCK-ON
T37A
T37A
T37A
T15A
T15A
T15A
VIN = standard color bar signal (1 Vp-p),
input +6 dB chroma signal level only,
measure T15A burst level, and calculate ratio
with VOR-15
VIN = standard color bar signal (1 Vp-p),
input –6 dB chroma signal level only,
measure T15A burst level, and calculate ratio
with VOR-15
VIN = standard color bar signal (1 Vp-p),
lower the chroma signal, and measure the
input burst level at the point where output at
T15A ceases, and calculate the ratio with the
standard input level
VOACCK T37A T15A Use a spectrum analyzer to measure the
output level at T15A in the killer state
described previously; ratio with VOR-15
VACCK-OFF T4A T34A Starting from the killer state described
previously, gradually raise the input chroma
level and measure the input burst level when
output is generated at T15A and calculate the
ratio with the standard input level
SVXO
T37A
T17
T19A
Measure the pin 17 DC voltage when a
standard color bar signal is input
(1 Vp-p)...V0
Measure the frequency at T19A when V0 is
applied to pin 17 from the external power
supply...f1
Measure the frequency at T19A when V0 +
10 mV is applied to pin 17...f2
SVXO =
f2 – f1 Hz/mV
10
fAPC1
fAPC2
tD
T37A
T37A
T37A
T15A
T15A
T32
T36
Input a 50% white signal overlapped with a
4.4336 MHz, 300 mVp-p continuous wave.
After confirming that there is output at T15A,
increase the frequency of the CW until the
output at T15A stops, and then gradually
reduce the frequency until output appears
again at T15A; that CW frequency is f1.
fAPC1 = f1 – 4433619 (Hz)
In the same manner, reduce the frequency of
the CW until the output at T15A stops, and
then gradually increase the frequency until
output appears again at T15A; that CW
frequency is f2.
fAPC2 = f2 – 4433619 (Hz)
Measure waveforms at T32 and T36 when a
standard color bar signal (1 Vp-p) is input.
min
450
–0.5
3.8
350
typ
560
0.2
–0.1
–26
–60
–20
5.7
440
–900
4.3
max Unit
670 mVp-p
0.5 dB
dB
dB
–50 dB
dB
7.6 Hz/mV
Hz
–350 Hz
µs
BGP pulse width
tW T37A T32
T36
4.8 µs
Continued on next page.
No. 5471 - 5/11

5 Page





LA7191N arduino
LA7191N
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment,
nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or
indirectly cause injury, death or property loss.
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors
and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and
expenses associated with such use:
2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO
ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume
production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of February, 1996. Specifications and information herein are subject to change without notice.
No. 5471 - 11/11

11 Page







PáginasTotal 11 Páginas
PDF Descargar[ Datasheet LA7191N.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LA7191NGlobal VHS-format VCR Video Signal ProcessorSanyo
Sanyo

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar