|
|
PDF M54972 Data sheet ( Hoja de datos )
| Número de pieza | M54972 | |
| Descripción | Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER | |
| Fabricantes | Mitsubishi | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M54972 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
MITSUBISHI <CONTROL / DRIVER IC>
M54972P/FP
Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER
DESCRIPTION
The M54972 is a semiconductor integrated circuit consisting of 8
stages of CMOS shift registers and latches with serial inputs and
serial or parallel outputs. It is based on Bi-CMOS process
technology, and has 8 bipolar drivers at the parallel outputs.
FEATURES
q Serial input and serial or parallel output
q Serial output enables cascade connection
q Built-in latch for each stage
q Enable input provides output control
q Low supply current (standby current ICC ≤ 10µA)
q Serial I/O level is compatible with typical CMOS devices
q Driver features: High withstand voltage (BVCEO ≥ 30V)
Capable of large drive currents (IO(max)=300mA)
Low output saturation voltage VOL < 0.6V at lo=300mA
q Wide operating temperature range Ta=-20 – +75°C
PIN CONFIGURATION (TOP VIEW)
Clock
T→ 1
Serial input S-IN → 2
Logic GND L-GND 3
Power supply VCC 4
Serial output S-OUT ← 5
Latch input LATCH → 6
Enable input
EN → 7
Driver GND P-GND 8
16 → O1
15 → O2
14 → O3
13 → O4
12 → O5
11 → O6
10 → O7
9 → O8
Outline 16P4(P)
16P2N-A(FP)
Parallel outputs
APPLICATION
Dot drivers for thermal print heads. Serial/parallel conversion.
Drivers for relays and solenoids.
FUNCTION
The M54972 consists of 8 stages of D-type flip flops connected to
8 latches.
Data is input to serial input S-IN, and clock pulses are input to
clock input T. When the clock changes from low to high, the input
data enters the first shift register and data already in the shift
registers is shifted sequentially.
The serial output S-OUT is used to connect multiple M54972 to
expand the number of parallel outputs. S-OUT is connected to S-IN
of the next stage.
For parallel output. When the clock pulse changes from low to
high, latch input (LATCH) is high and output enable input (EN) is
low the serial input data at S-IN appears at output O1 and the other
data already present is shifted sequentially to outputs O2 through
O8.
The parallel outputs are inverted.
When the latch input is held low, the latch retains the stored data.
When the EN input is high, outputs O1 through O8 all turn off. As
the internal logic is unstable when the power is turned on, the EN
input should be kept high (setting outputs O1 through O8 off) until
input data is set and the internal logic is initialized.
L-GND is the GND of CMOS logic circuit and P-GND is the GND of
output driver circuits O1 through O8 which employ bipolar
transistors capable of large drive currents.
BLOCK DIAGRAM
Parallel outputs
O1 O2 O3 O4 O5 O6 O7 O8
16 15 14 13 12 11 10
9
Power supply
VCC 4
8 P-GND Driver GND
Enable input
EN 7
Latch input LATCH 6
Q QQQ QQQ Q
LD LD LD LD LD LD LD LD
Serial input S-IN 2
Clock
T1
DQ DQ DQ DQ DQ DQ DQ DQ
TTTTTTTT
3
L-GND
Logic GND
5 S-OUT Serial output
1 page  
MITSUBISHI <CONTROL / DRIVER IC>
M54972P/FP
Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER
TYPICAL CHARACTERISTICS (VCC=5V, Ta=25°C, unless otherwise noted)
Thermal derating
(Absolute maximum rating)
1.5
M54972P
VCC vs. ICC
100
1.0 M54972FP
80
60
40
0.5
20
0
0 25 50 75
Ambient temperature Ta (°C)
100
0
34567
Supplyvoltage VCC (V)
8 Outputs ON
7 Outputs ON
6 Outputs ON
5 Outputs ON
4 Outputs ON
3 Outputs ON
2 Outputs ON
1 Output ON
8
Duty cycle vs. allowable output current
(M54972P)
400
Duty cycle vs. allowable output current
(M54972P)
400
300 1 – 6
7
8
200
Ta = 25°C, VCC = 6V
100
Repetitive frequency >10HZ
Each figure in a circle shows the number
of output circuits which operate
simultaneously.
Current value : output current per circuit
0
0 20 40 60 80 100
Duty cycle (%)
Duty cycle vs. allowable output current
(M54972FP)
300 1 – 3
4
5
200
6
8
100 Ta = 25°C, VCC = 6V
Repetitive frequency >10HZ
Each figure in a circle shows the number
of output circuits which operate
simultaneously.
Current value : output current per circuit
0
0 20 40 60 80 100
Duty cycle (%)
300 1 – 3
4
5
200 6
7
Ta = 75°C, VCC = 6V
8
100
Repetitive frequency >10HZ
Each figure in a circle shows the number
of output circuits which operate
simultaneously.
Current value : output current per circuit
0
0 20 40 60 80 100
Duty cycle (%)
Duty cycle vs. allowable output current
(M54972FP)
300 1 2
3
200
4
100 Ta = 75°C, VCC = 6V
Repetitive frequency >10HZ
Each figure in a circle shows
the number of output circuits which
operate simultaneously.
Current value : output current per circuit
0
0 20 40 60 80
6
8
100
Duty cycle (%)
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet M54972.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M54970P | 9-Bit Serial Input / Latched Driver |  Mitsubishi Electric |
| M54972 | Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER | Mitsubishi |
| M54972 | Bi-CMOS 8-BIT SERIAL-INPUT LATCHED DRIVER | Mitsubishi |
| M54974P | Bi-CMOS 12-BIT SERIAL-INPUT LATCHED DRIVER | Mitsubishi |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |