|
|
PDF IC693MDL760 Data sheet ( Hoja de datos )
| Número de pieza | IC693MDL760 | |
| Descripción | Solenoid Valve Output Module | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IC693MDL760 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
GFK-1881A
November 2000
Solenoid Valve Output Module
IC693MDL760
Product Description
Description
This IC693MDL760 output module provides eleven
pneumatic outputs and five 24VDC sourcing outputs. For
each pneumatic output, the module contains an internal 3-
way solenoid-actuated valve and an associated output
fitting, which is located on the front panel. When an
output is turned ON, its internal valve connects a user-
supplied pressure source (100 psi maximum) to the output
fitting. The pressure source is connected to the fitting on
the bottom of the module. When the output is turned
OFF, the valve’s output port is vented to atmosphere
inside the module. Solenoid power is supplied from an
external 24VDC source to the “DC Outputs” connector on
the front panel.
A 12-pin connector, located on the module’s front panel,
allows the user to connect the optional IC693ACC760
Solenoid Forcing Pendent, described later.
The five 24VDC outputs can each drive up to a maximum
0.5A, with a limit of 2.0A total for all five points. Field
wiring is connected to these outputs via a 10-pin
connector located on the front panel. The user must
provide 24VDC to this connector to power the positive
logic outputs, which source current to the field
connections. This group of five discrete outputs is
electrically isolated from the PLC backplane; however,
the outputs are not individually isolated from each other.
The module is accessed from the logic program as a
standard 16-point output module. When using VersaPro
version 2.0 (or later version) programming software, it
should be configured by its catalog number. When using
programming software other than VersaPro version 2.0
(or later version), the module must be configured as a
standard 16-point generic output module.
PWR
11
2
23
4
35
6
47
8
9
5 10
61
2
73
4
85
9
10
11
Figure 1. IC693MDL760 Module
The module is enclosed in a standard IC693 plastic
housing.
1 page  
www.DataSheet4U.com
Solenoid Valve Output Module
5
GFK-1881A
Field Connectors
The following specifications are for the mating connectors (not supplied with the module) for the
module’s two faceplate connectors (“Pendent” and “DC Output”).
Pendent Connector (Supplied with Optional Pendent)
Item
Vendor
Part Number Note
Male Housing
AMP
87631-7
12-pin connector housing
Crimp Contacts (12
required)
AMP
1-87523-9
Female pins, rated for AWG 20-24
gauge wire
Crimping Tool
AMP
90202-2
DC Output Connector
Item
Male Housing
Crimp Contacts (10
required)
Crimping Tool
Vendor
AMP
AMP
AMP
Part Number Notes
87631-5
10-pin connector housing
1-87523-9
Female pins, rated for AWG 20-24
gauge wire
90202-2
Pneumatic Fitting Specifications and Installation Instructions
Module
Fitting
Number
per Module
Vendor
Part
Number
Notes
Front 11
Clippard 11752-2 10-32 threads, 1/16″ hose barb, 1/4″ hex. shoulder
Bottom 1
Clippard 11752-3 10-32 threads, 1/8″ hose barb, 1/4″ hex. shoulder
Due to limited room in the module’s packing container, it is necessary to ship the module with its fittings
removed. Use the following guidelines to install the fittings on the module:
• Place the provided gasket over the threaded end of the fitting and carefully push it over the threads
until it stops against the hexagonal shoulder.
• Carefully thread the fitting into the manifold by hand.
• Tighten the fitting to a maximum of 7 to 9 inch/pounds.
Caution
Overtightening may cause a fitting to crack or snap off, or could result in thread
damage. Limit tightening torque to 7 to 9 inch/pounds.
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet IC693MDL760.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IC693MDL760 | Solenoid Valve Output Module | ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |