|
|
Número de pieza | TDA7056A | |
Descripción | 3 W BTL mono audio output amplifier with DC volume control | |
Fabricantes | NXP Semiconductors | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TDA7056A (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
No Preview Available ! INTEGRATED CIRCUITS
DATA SHEET
TDA7056A
3 W BTL mono audio output
amplifier with DC volume control
Product specificiation
File under Integrated Circuits, IC01
July 1994
1 page Philips Semiconductors
3 W BTL mono audio output amplifier with
DC volume control
Product specificiation
TDA7056A
CHARACTERISTICS
VP = 12 V; f = 1 kHz; RL = 16 Ω; Tamb = 25 °C; unless otherwise specified (see Fig.6)
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
VP positive supply voltage range
IP total quiescent current
Maximum gain (V5 = 1.4 V)
PO output power
THD
Gv
VI
Vno(rms)
B
total harmonic distortion
voltage gain
input signal handling
noise output voltage (RMS value)
bandwidth
SVRR
supply voltage ripple rejection
|Voff|
DC output offset voltage
ZI input impedance pin 3
Minimum gain (V5 = 0.5 V)
Gv
Vno(rms)
voltage gain
noise output voltage (RMS value)
Mute position
4.5
VP = 12 V; RL = ∞; note 1 −
−
8
18 V
16 mA
THD = 10%; RL = 16 Ω
THD = 10%; RL = 8 Ω
PO = 0.5 W
V5 = 0.8 V;THD < 1%
f = 500 kHz; note 2
at −1 dB
note 3
3 3.5
−W
− 5.2
−W
− 0.3
1%
34.5 35.5
36.5 dB
0.5 0.65 − V
− 210 − µV
− 20 Hz to −
300 kHz
38 46
− dB
−0
150 mV
15 20
25 kΩ
note 4
− −44 − dB
− 20
30 µV
VO output voltage in mute position
DC volume control
V5 ≤ 0.3 V; VI = 600 mV −
−
30 µV
φ gain control range
I5 control current
V5 = 0 V
75 80
60 70
− dB
80 µA
Notes to the characteristics
1. With a load connected to the outputs the quiescent current will increase, the maximum value of this increase being
equal to the DC output offset voltage divided by RL.
2. The noise output voltage (RMS value) at f = 500 kHz is measured with RS = 0 Ω and bandwidth = 5 kHz.
3. The ripple rejection is measured with RS = 0 Ω and f = 100 Hz to 10 kHz. The ripple voltage of 200 mV (RMS value)
is applied to the positive supply rail.
4. The noise output voltage (RMS value) is measured with RS = 5 kΩ unweighted.
July 1994
5
5 Page |
Páginas | Total 9 Páginas | |
PDF Descargar | [ Datasheet TDA7056A.PDF ] |
Número de pieza | Descripción | Fabricantes |
TDA7056 | 3 W mono BTL audio output amplifier | NXP Semiconductors |
TDA7056A | 3 W BTL mono audio output amplifier with DC volume control | NXP Semiconductors |
TDA7056AT | 3 W mono BTL audio amplifier with DC volume control | NXP Semiconductors |
TDA7056B | 5 W mono BTL audio amplifier with DC volume control | NXP Semiconductors |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |