DataSheet.es    


PDF TDA4814 Data sheet ( Hoja de datos )

Número de pieza TDA4814
Descripción Power Factor Controller IC for High Power Factor and Active Harmonic Filter
Fabricantes Siemens Semiconductor 
Logotipo Siemens Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de TDA4814 (archivo pdf) en la parte inferior de esta página.


Total 14 Páginas

No Preview Available ! TDA4814 Hoja de datos, Descripción, Manual

Power Factor Controller
IC for High Power Factor and
Active Harmonic Filter
Features
q IC for sinusoidal line-current consumption
q Power factor approaching 1
q Controls boost converter as an active harmonics filter
q Direct drive of SIPMOS transistor
q Zero crossing detector for discontinuous operation mode
with variable frequency
q 110/220 V AC operation without switchover
q Standby current consumption of 0.5 mA
q Start/stop monitoring circuit for lamp generators
P-DIP-14-1
TDA 4814
Bipolar IC
Type
Ordering Code
s TDA 4814 A
Q67000-A8163
s Not for new design
Package
P-DIP-14-1
Semiconductor Group
1
01.96

1 page




TDA4814 pdf
TDA 4814
Output Driver
The output driver is intended to drive a SIPMOS transistor directly. It is designed as a push-pull
stage.
Both the capacitive input impedance and keeping the gate level at zero potential in standby
operation by an internal 10-k-resistor are taken into account. Possible effects on the output driver
by line inductances or capacitive couplings via SIPMOS transistor Miller capacitance are limited by
diodes connected to ground and supply voltage.
Ground Pins
Between the ground pins GND and GND QSIP, a very close and low-impedance connection is to
be established.
Monitoring Circuit (I START, I STOP, Q START, Q STOP)
The monitoring circuit guarantees the secure operation of subsequent circuitries.
Any circuitry that is shut down because of a fault, for instance, cannot be started up again until the
monitoring start (I START / Q START) has turned on and a positive voltage pulse has been
impressed on Q START. This function starts for example the lamp generator of an electronic ballast
or generates auxiliary trigger signals for the detector input.
If there is a defect present (e.g. defective fluorescent lamp) the monitoring stop (I STOP /
Q STOP) will shut down either the entire unit or simply the circuitry that has to be protected. No
restart is possible then until the hold current impressed on I START or Q STOP has been
interrupted (e.g. by a power down).
Semiconductor Group
5

5 Page





TDA4814 arduino
TDA 4814
Multiplier Characteristics
Semiconductor Group
11

11 Page







PáginasTotal 14 Páginas
PDF Descargar[ Datasheet TDA4814.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TDA4810SYNC PROCESSOR AND HORIZONTAL DRIVE FOR MONITORSNXP Semiconductors
NXP Semiconductors
TDA4814Power Factor Controller IC for High Power Factor and Active Harmonic FilterSiemens Semiconductor
Siemens Semiconductor
TDA4817Power Factor Controller IC for High Power Factor and Active Harmonic FilteringSiemens Semiconductor
Siemens Semiconductor
TDA4817GPower Factor Controller IC for High Power Factor and Active Harmonic FilteringSiemens Semiconductor
Siemens Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar