|
|
PDF TDA4605-2 Data sheet ( Hoja de datos )
| Número de pieza | TDA4605-2 | |
| Descripción | Control IC for Switched-Mode Power Supplies using MOS-Transistors | |
| Fabricantes | Siemens Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA4605-2 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
Control IC for Switched-Mode Power Supplies
using MOS-Transistors
TDA 4605-2
Bipolar IC
Features
q Fold-back characteristics provides overload protection for
external components
q Burst operation under secondary short-circuit condition
implemented
q Protection against open or a short of the control loop
q Switch-off if line voltage is too low (undervoltage switch-off)
q Line voltage depending compensation of fold-back point
q Soft-start for quiet start-up without noise generated by the
transformer
q Chip-over temperature protection implemented (thermal
shutdown)
q On-chip ringing suppression circuit against parasitic
oscillations of the transformer
P-DIP-8-1
Type
TDA 4605-2
Ordering Code
Q67000-A5020
Package
P-DIP-8-1
The IC TDA 4605-2 controls the MOS-power transistor and performs all necessary regulation and
monitoring functions in free running flyback converters. Because of the fact that a wide load range
is achieved, this IC is applicable for consumer as well as industrial power supplies.
The serial circuit and primary winding of the flyback transformer are connected in series to the input
voltage. During the switch-on period of the transistor, energy is stored in the transformer. During the
switch-off period the energy is fed to the load via the secondary winding. By varying switch-on time
of the power transistor, the IC controls each portion of energy transferred to the secondary side
such that the output voltage remains nearly independent of load variations. The required control
information is taken from the input voltage during the switch-on period and from a regulation winding
during the switch-off period. A new cycle will start if the transformer has transferred the stored
energy completely into the load.
Semiconductor Group
54
06.94
1 page  
TDA 4605-2
Circuit Description
Application Circuit
The application circuit shows a flyback converter for video recorders with an output power rating of
70 W. The circuit is designed as a wide-range power supply for AC-line voltages of 180 to 264 V.
The AC-input voltage is rectified by the bridge rectifier GR1 and smoothed by C1 . The NTC limits
the rush-in current.
The IC includes an internal circuit to avoid the turn-on of the power transistor T1 because of static
charges applied to the transistors gate, during the turn-off state of the IC. The resistor R 13 helps to
limit the spectrum of the radiated noise.
During the conductive phase of the power transistor T1 the current rise in the primary winding
depends on the winding inductance and the mains voltage.
The network consisting of R 4-C5 is used to create a model of the sawtooth shaped rise of the
collector current. The resulting control voltage is fed into pin 2 of the IC. The RC-time constant given
by R 4-C5 must be designed that way that driving the transistor core into saturation is avoided.
The ratio of the voltage divider R 10/R 11 is fixing a voltage level threshold. Below this threshold the
switching power supply shall stop operation because of the low mains voltage. The control voltage
present at pin 3 also determines the correction current for the foldback point.
This current added to the current flowing through R 4 and represents an additional charge to C5 in
order to reduce the turn-on phase of T1. This is done to stabilize the fold-back point even under
higher mains voltages.
The control of the switched-mode power supply is done by means of a control voltage applied to
pin 1. The control voltage of winding n1 during the off-period of T1 is rectified by D3 smoothed by C6
and stepped down at an adjustable ratio by R 5 , R 6 and R 7 . The primary peak current, is adjusted
by the IC so that the voltage applied across the control winding, and hence the output voltages, are
at the desired level.
When the energy stored in the transformer is transferred into the load the control voltage passes
through zero. The IC detects the zero crossing via the series R 9 connected to pin 8. But zero
crossings of the control voltage can also be produced by ringing of the transformer after the turn-off
of the power transistor for T1 or when a short-circuit is applied to the output of the SMPS.
The capacitor C8 is connected to pin 7. During the start-up phase this capacitor assures pulses with
a shorter duty cycle in order to keep the operating frequency outside the audible frequency range.
On the secondary side of the transformer 3 output voltages are produced using the windings n 2 to
n5 , rectified by D4 to D6 and smoothed by C9 to C11 . The resistor R 12 is used as a bleeder resistor,
the resistors with implemented fuse R 15 and R 16 protect the rectifies against short circuits in the
output circuits, which are designed to supply only small loads.
Semiconductor Group
58
5 Page 
TDA 4605-2
Characteristics (cont’d)
TA = 25 ˚C; VS = 10 V
Parameter
Symbol
Limit Values
Unit
min. typ. max.
Test Condition
Generally Valid Data (V6 = 10 V)
Voltage of the Zero Transition Detector
Positive clamping
voltage
V8P
0.75
Negative clamping
voltage
V8N
– 0.2
Threshold value
Suppression of
transformer ringing
V8S
tUL
40 50
4 4.5
Input current
– I8 0
5.5
4
Push-Pull Output Stage
Saturation voltages
Pin 5 sourcing
Pin 5 sinking
Pin 5 sinking
VSat0
VSatV
VSatV
1.5 2.0
1.0 1.2
1.4 1.8
Output Slew Rate
Rising edge
Falling edge
+ dV5/dt
+ dV5/dt
20
50
Reduction of Control Voltage
Current to reduce the – I1
control voltage
50
V I8 = 1 mA
V I8 = – 1 mA
mV
µs
µA V8 = 0
V I5 = – 0.1 A
V I5 = + 0.1 A
V I5 = + 0.5 A
V/µs
V/µs
µA V7 = 1.1 V
Test
Circuit
2
2
2
2
1
1
1
2
2
Semiconductor Group
64
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet TDA4605-2.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA4605-2 | Control IC for Switched-Mode Power Supplies using MOS-Transistors | Siemens Semiconductor |
| TDA4605-3 | Control IC for Switched-Mode Power Supplies using MOS-Transistor | Siemens Semiconductor |
| TDA4605-3 | PWM-QR IC |  Infineon |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |