|
|
PDF TDA3602 Data sheet ( Hoja de datos )
| Número de pieza | TDA3602 | |
| Descripción | Multiple output voltage regulator | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA3602 (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA3602
Multiple output voltage regulator
Product specification
File under Integrated Circuits, IC01
July 1994
1 page  
Philips Semiconductors
Multiple output voltage regulator
Product specification
TDA3602
PINNING
SYMBOL PIN
VP
REG1
1
2
RESET 3
Vsc
HOLD
4
5
GND
6
REG3 7
Vbu
REG2
8
9
DESCRIPTION
positive supply voltage
Regulator 1 output
reset output
state control input
hold output
ground
Regulator 3 output
back-up
Regulator 2 output
handbook, halfpage
VP 1
REG1 2
RESET 3
Vsc 4
HOLD 5
TDA3602
GND 6
REG3 7
V bu 8
REG2 9
MCD345
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
This multiple output voltage regulator contains three fixed
voltage regulators, numbered 1, 2 and 3. Two of these can
be switched between the on and off states using the state
control pin (pin 4). The third (Regulator 3), which is
continuously in, can be switched by the state control pin
between a low and a high current mode.
In addition to Regulators 1 and 2, the device is supplied by
an internal switch that is open when the supply voltage
falls below the back-up voltage (negative field decay or
engine start procedure), or during a load dump. (During
this load dump, Regulators 1 and 2 are switched off and
RESET is switched LOW). This switched supply voltage
(the so-called back-up voltage (Vbu), is available at pin 8.
An electrolytic capacitor can be connected to this pin, and
the charge on this capacitor can be used to supply the
device for a short period after the supply voltage is
removed.
Three pins are provided for interfacing with a
microprocessor:
• state control pin
• hold output pin
• reset output pin.
When the supply voltage (VP) is connected to the device,
Vbu will rise. When Vbu reaches 7.9 V, the device is in the
power-on mode. The RESET output goes HIGH and
Regulator 3 is switched on. In a microprocessor
application, the RESET output can be used to call up the
CPU and to initialize the program.
What follows depends on the voltage at the state control
pin (Vsc). In most applications, when the supply voltage is
connected, Vsc will rise slowly (e.g. by charging a
capacitor).The device will leave the power-on mode and
enter the reset mode when Vsc rises above 2.2 V. In both
the power-on and reset modes, Regulator 3 will be in the
high current mode, Regulators 1 and 2 will be switched off
and the RESET output will be HIGH.
The device will enter the wake mode when Vsc reaches 2.8
V. The RESET pin will go LOW and the CPU must be
switched to the sleep mode. Regulator 3 is still in the high
current mode.
As Vsc continues rising and the voltage reaches 3.6 V, the
stabilizer will be switched into the sleep mode. It will be in
a coma mode when Vsc is greater than 3.8 V. In this mode,
only the relevant circuits remain operating; this is to keep
the power consumption as low as possible i.e. typically 290
µA.
If the device is switched on with Vsc already higher than 3.8
V, the device will be switched directly from the power-on
mode into the coma mode.
When Vsc is lowered gradually from 3.6 V (or higher) to 2
V, the device will go from sleep to reset again.
Vsc must be lower than 1.1 V to bring the device into the on
mode; note that this is not the same as the power-on
mode. In this condition, Regulator 3 is in the high current
mode, both Regulators 1 and 2 are switched on and the
HOLD output will be HIGH (depending on the state of VP
and the in-regulation condition of Regulators 1 and 2).
July 1994
5
5 Page 
Philips Semiconductors
Multiple output voltage regulator
Product specification
TDA3602
handbook, full pagewidth VP
V bu
REGULATOR 3
state control
reset
REGULATORS
1 and 2
hold
Fig.4 Timing diagram.
Table 2 Logic table HOLD function.
INPUTS FOR HOLD (note 1)
VBU
VP SCHMITT
TRIGGER
ON STATE
10
01
11
11
11
11
X
X
0
1
1
1
Note
1. 0 = off; 1 = on; X = don't care.
REG1
0
0
0
0
X
1
MCD348
REG2
0
0
0
X
0
1
OUTPUT
HOLD
0
0
0
0
0
1
July 1994
11
11 Page | ||
| Páginas | Total 26 Páginas | |
| PDF Descargar | [ Datasheet TDA3602.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA3601AQ | Multiple output voltage regulators | NXP Semiconductors |
| TDA3601Q | Multiple output voltage regulators | NXP Semiconductors |
| TDA3602 | Multiple output voltage regulator | NXP Semiconductors |
| TDA3603 | Multiple voltage regulator with switch | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |