|
|
PDF TDA16847G Data sheet ( Hoja de datos )
| Número de pieza | TDA16847G | |
| Descripción | ICs for Consumer Electronics | |
| Fabricantes | Infineon Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA16847G (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
|
No Preview Available !
ICs for Consumer Electronics
Controller for Switch Mode Power Supplies Supporting Low Power
Standby and Power Factor Correction
TDA 16846/TDA 16847
Data Sheet 2000-01-14
1 page  
TDA 16846
TDA 16847
1.4 Short Description of the Pin Functions
Pin Function
1 A parallel RC-circuit between this pin and ground determines the ringing
suppression time and the standby-frequency.
2 A capacitor between this pin and ground and a resistor between this pin and
the positive terminal of the primary elcap quantifies the max. possible output
power of the SMPS.
3 This is the input of the error amplifier and the zero crossing input. The output
of a voltage divider between the control winding and ground is connected to
this input. If the pulses at pin 3 exceed a 5 V threshold, the control voltage at
pin 4 is lowered.
4 This is the pin for the control voltage. A capacitor has to be connected
between this pin and ground. The value of this capacitor determines the
duration of the softstart and the speed of the control.
5 If an opto coupler for the control is used, it’s output has to be connected
between this pin and ground. The voltage divider at pin 3 has then to be
changed, so that the pulses at pin 3 are below 5 V.
6 Fault comparator 2: If a voltage > 1.2 V is applied to this pin, the SMPS stops.
7 If fixed frequency mode is wanted, a parallel RC circuit has to be connected
between this pin and ground. The RC-value determines the frequency. If
synchronized mode is wanted, sync pulses have to be fed into this pin.
8 Not connected (TDA 16846). / This is the power measurement output of the
Temporary High Power Circuit. A capacitor and a RC-circuit has to be
connected between this pin and ground (TDA 16847).
9 Output for reference voltage (5 V). With a resistor between this pin and ground
the fault comparator 2 (pin 6) is enabled.
10 Fault comparator 1: If a voltage > 1 V is applied to this pin, the SMPS stops.
11 This is the input of the primary voltage check. The voltage at the anode of the
primary elcap has to be fed to this pin via a voltage divider. If the voltage of
this pin falls below 1 V, the SMPS is switched off. A second function of this pin
is the primary voltage dependent fold back point correction (only active in free
running mode).
12 Common ground.
13 Output signal. This pin has to be connected across a serial resistor with the
gate of the power transistor.
14 Connection for supply voltage and startup capacitor. After startup the supply
voltage is produced by the control winding of the transformer and rectified by
an external diode.
Data Sheet
5 2000-01-14
5 Page 
TDA 16846
TDA 16847
External
From SYNC
Control Voltage
Limit
1.5 V
OTC 1
2V
OFTC
+
-
1
R1 C1
ED3
Internal
OFTCD
+
-
&
I1
2V
ED2
1
From Error FF
ONTF
S
Q
R
Output
Driver
&
3.5 V
RZI 3
RSTC
+
-
RSTC
S
Q
R
ED1
From ONTC From UVLO
Ringing Suppression Time
Zero Crossing Signal
Figure 6 Off-Time-Circuit
AES02651
Data Sheet
11 2000-01-14
11 Page | ||
| Páginas | Total 28 Páginas | |
| PDF Descargar | [ Datasheet TDA16847G.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA16847 | (TDA1684x-x) Controller | Infineon Technologies |
| TDA16847-2 | (TDA1684x-x) Controller | Infineon Technologies |
| TDA16847G | ICs for Consumer Electronics | Infineon Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |