DataSheet.es    


PDF TDA1596 Data sheet ( Hoja de datos )

Número de pieza TDA1596
Descripción IF amplifier/demodulator for FM radio receivers
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de TDA1596 (archivo pdf) en la parte inferior de esta página.


Total 20 Páginas

No Preview Available ! TDA1596 Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
DATA SHEET
TDA1596
IF amplifier/demodulator for
FM radio receivers
Product specification
File under Integrated Circuits, IC01
April 1991

1 page




TDA1596 pdf
Philips Semiconductors
IF amplifier/demodulator for
FM radio receivers
Product specification
TDA1596
FUNCTIONAL DESCRIPTION
Limiter-amplifier
This has five stages of IF amplification using balanced differential limiter-amplifiers with emitter-follower coupling.
Decoupling of the stages from the voltage supply lines and an internal high-ohmic DC feed-back loop give a very stable
IF performance. The amplifier gain is virtually independent from temperature changes.
FM demodulator
The demodulator is fully balanced and comprises two cross-coupled differential amplifiers. Quadrature detection of the
FM signal is performed by feeding one differential amplifier directly from the limiter-amplifier output, and the other via an
external 90° phase-shifting network. The demodulator has good stability and its zero cross-over shift is small.
The bandwidth of the demodulator output is restricted to approximately 1 MHz by an internal low-pass filter.
THD compensation
This circuit compensates non-linearities introduced by demodulation. For this to operate correctly the demodulator circuit
between pins 9 and 10 must have a loaded Q-factor of 19. Consequently there is no need for the demodulator tuned
circuit to be adjusted for minimum THD, instead the adjustment criterium is for a symmetrical stop pulse.
Mute attenuator and AF output
The control voltage for the mute attenuator at pin 14 is generated from the values of the level detector and the detuning
detector outputs. The mute attenuator has a fast attack and a slow decay which is determined by the capacitor at pin 14.
The AF signal is passed via the mute attenuator to the output at pin 4.
A weighted control voltage, available from pin 6, is obtained from the mute attenuator control voltage via a buffer-amplifier
which introduces an additional voltage shift and gain.
Level detector
The level detector generates a voltage output which is proportional to the field strength of the input signal.
The unweighted level detector output is available when the mode switch is operating in the FM, mute-on condition.
Tuning-stop outputs
The open collector outputs STOP-0 and STOP-1 (from pins 13 and 12 respectively) are voltages derived from the
detuning level and the field strength of the input signal. If only one tuning-stop output is required, pins 12 and 13 may be
tied together.
April 1991
5

5 Page





TDA1596 arduino
Philips Semiconductors
IF amplifier/demodulator for
FM radio receivers
Product specification
TDA1596
April 1991
11

11 Page







PáginasTotal 20 Páginas
PDF Descargar[ Datasheet TDA1596.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TDA1591PLL stereo decoder and noise blankerNXP Semiconductors
NXP Semiconductors
TDA1591TPLL stereo decoder and noise blankerNXP Semiconductors
NXP Semiconductors
TDA1592PLL stereo decoder and noise blankerNXP Semiconductors
NXP Semiconductors
TDA1592TPLL stereo decoder and noise blankerNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar