|
|
PDF TDA1555Q Data sheet ( Hoja de datos )
| Número de pieza | TDA1555Q | |
| Descripción | 4 x 11 W single-ended or 2 x 22 W power amplifier with distortion detector | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA1555Q (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA1555Q
4 x 11 W single-ended or 2 x 22 W
power amplifier with distortion
detector
Product specification
File under Integrated Circuits, IC01
May 1992
1 page  
Philips Semiconductors
4 x 11 W single-ended or 2 x 22 W power
amplifier with distortion detector
Product specification
TDA1555Q
Fig.2 Power derating curve.
DC CHARACTERISTICS
VP = 14.4 V; Tamb = 25 °C; measurements taken using Fig.4; unless otherwise specified
PARAMETER
CONDITIONS
SYMBOL MIN.
Supply
Supply voltage range
Total quiescent current
DC output voltage
DC output offset voltage
Mute/stand-by switch
Switch-on voltage level
Mute condition
Output signal in mute
position
DC output offset voltage
(between pins 6 to 8
and 10 to 12)
Stand-by condition
DC current in stand-by condition
Switch-on current
note 1
note 2
VI = 1 V (max.);
f = 1 kHz
VP
Itot
VO
|∆VO|
VON
Vmute
VO
6.0
−
−
−
8.5
3.3
−
|∆VO|
Vsb
Isb
Isw
−
0
−
−
TYP.
14.4
80
6.9
−
−
−
−
−
−
−
12
MAX. UNIT
18.0 V
160 mA
−V
100 mV
−V
6.4 V
2 mV
100 mV
2V
100 µA
40 µA
May 1992
5
5 Page 
Philips Semiconductors
4 x 11 W single-ended or 2 x 22 W power
amplifier with distortion detector
Product specification
TDA1555Q
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
May 1992
11
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet TDA1555Q.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA1555 | 4 x 11 W single-ended or 2 x 22 W power amplifier with distortion detector | NXP Semiconductors |
| TDA1555Q | 4 x 11 W single-ended or 2 x 22 W power amplifier with distortion detector | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |