DataSheet.es    


PDF TC9316F Data sheet ( Hoja de datos )

Número de pieza TC9316F
Descripción DTS MICRO CONTROLLER CONTAINING PLL / LCD DRIVER
Fabricantes Toshiba 
Logotipo Toshiba Logotipo



Hay una vista previa y un enlace de descarga de TC9316F (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! TC9316F Hoja de datos, Descripción, Manual

TC9316F/FA/FB
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC9316F,TC9316FA,TC9316FB
DTS Micro Controller Containing PLL, LCD Driver (DTS-11)
TC9316F/FA/FB are a 4 bit CMOS microcontroller for digital
tuning system capable of making 3 V low voltage operation, and
containing PLL circuit, LCD driver.
CPU has 4 bit parallel addition and substruction (AI/SI
instructions, etc.), logical operation (OR and AN instructions,
etc.), plural bit judge, comparison instructions (TM, SL
instructions, etc.) and time base function.
The package is 60 pin mini-flat type (TC9316F), 64 pin
mini-flat type (TC9316FA, TC9316FB) and has abundant I/O
ports and exclusive key-input ports controlled by the powerful
input/output instructions (IO, KEY instructions), besides
containing PLL circuit.
By combining with the prescaler TD6134AF or TD7101F or
TD7103F, it permits the configuration of DTS that receives
FM/AM and TV (VHF) bands.
TC9316F
TC9316FA
Features
x 4 bit micro controller for digital tuning system use
x It is operated with 3 V single power supply. (VDD = 1.8~3.6 V)
x Back-up of data memory (RAM) and each port are easily made.
(by INH terminal)
TC9316FB
x Built-in LCD driver (1/3 duty, 1/2 bias driving, driving
frequency: 52 Hz), and boosting circuit for display
x Program memory (ROM): 16 bit × 2048 steps
x Data memory (RAM): 4 bit × 128 words
x Powerful instruction set of 65 kinds. (all single word
instruction)
x Instruction executing time 80 µs. (75 kHz crystal connection)
x Abundant addition and substruction instructions.
(addition instructions 12 kinds, substraction instructions 12
kinds)
x Powerful compound judge instructions. (TMTR, TMFR, TMT,
TMF, TMTN, TMFN instructions)
Weight
QFP60-P-1414-0.80E: 0.85 g (typ.)
LQFP64-P-1010-0.50: 0.32 g (typ.)
QFP64-P-1212-0.65: 0.45 g (typ.)
x Data transfer in same low address is possible.
x Indirect transfer of register is possible. (MVRD, MVRS, MVGD, MVGS instructions)
x 16 powerful general registers. (arranged in RAM)
x Stack level: 1 level
x Program memory (ROM) has no conception of page, field, and JUMP and CAL instruction can be freely made
among 2048 steps.
x At the FM or TV band, swallow counter is composed by combining with prescaler TD6134AF or TD7103F, and is
able to receive TV VHF band. At the AM or FM band, swallow counter is composed by combining with prescaler
TD7101F, and is able to receive SW, AM, FM band.
x It is possible to freely refer to the content, 16 bits, of optional address within 1024 steps in program memory
(ROM). (DAL instruction)
x Independent frequency input terminal at FM and AM (FMIN, AMIN), and two phase-comparator outputs. (DO1,
DO2)
x 7 kinds of reference frequency can be selected with program.
1 2003-06-27

1 page




TC9316F pdf
Pin Function
(data in parenthesises are for TC9316FA, TC9316FB)
Pin No. Symbol
Pin Name
Explanation of Function and Operation
58
COM1
(61)
59
COM2
(62)
60
COM3
(63)
1~12 S1~S12
13~20
13~15
17~21
S13/KR7~
S20/KR0
LCD Common
Output
This is a common signal output terminal to LCD.
Indication of maximum 60 segments is possible
with matrix made with S1~S20.
To this terminal, three value levels of VDD, VEE,
VLCD are output with 3.2 ms interval and 52 Hz
cycle.
LCD Segment
Output
LCD Segment
Output/Key Return
Output
This is a segment signal output terminal to LCD.
Indication of maximum 60 segments is possible
with matrix made with COM1, COM2 and COM3.
The data for these terminals are output by the
execution of SEG instruction and MARK
instruction.
S13/KR7~S20/KR0 are able to output LCD
segment signal and Key Return Timing signal at
same time by program.
Maximum 32 ( 8 u 4) Key input be able to
combine with matrix made with Key input ports
K0~K3 without the other output port.
TC9316F/FA/FB
Remarks
21, 22
24, 25
22, 23
25, 26
K0~K3
Key Input Port
This is a 4 bit input port for key matrix input.
It is able to input data of maximum total 56 key,
maximum 24 key ( 6 u 4) with matrix made with
Key Return Timing output port, besides maximum
32 key (8 u 4) with matrix made with LCD
Segment Output S13/KR7~S20/KR0.
All these terminals are built in pull down
resistances.
26~29
T0~T3
(27~30)
30, 31
OT0, OT1
(31, 33)
General Purpose
/Key Return Timing
Output Port
This is a 6 bit output port for General Purpose/Key
Return Timing output.
Besides use for general purpose output port, it is
able to output the timing signal for key matrix by
program.
For making the key matrix, it is built in load
resistance at N-ch FET side, useless the diode
when uses Push key.
32~35
P1-0~P1-3
(34~37)
I/O Port
36
(38)
P2-0/BUZR
I/O Port/Buzzer
Pulse Output Port
37~39
P2-1~P2-3
(34~41)
I/O Port
This is a 8 bit general purpose I/O Port.
It is possible to assign input and output for each
bit by program.
P2-0 is able to use as the beep sound pulse
output port by program.
It is able to output 3 kinds of the beep sound pulse
signal by program.
5 2003-06-27

5 Page





TC9316F arduino
TC9316F/FA/FB
11. Explanation List of Function and Operation of Instructions (explanation of symbols)
M: Data memory address
Normally, one of 00H~3FH address of data memory.
r: General register
One of 00H~0FH address of data memory.
PC: Program counter (11 bit)
STACK: Stack register (11 bit)
G: G-register (3 bit)
DATA: Data register (16 bit)
I: Immediate data (4 bit)
N: Bit position (4 bit)
: All “0”
C: Code No. of port (4 bit)
CN: Lower rank 3 bit of port code No.
RN: General register No. (4 bit)
ADDR1: Program memory address in page 0 or 1 (10 bit)
ADDR2: Higher rank 6 bit of program memory address in page 0
Ca: Carry
b: Borrow
PLL: Port treated during the execution of PLL instruction
SEG: Port treated during the execution of SEG instruction
MARK: Port treated during the execution of MARK instruction
IO: Port treated during the execution of IO instruction
KEY: Port treated during the execution of KEY instruction
( ): Register or data memory content
[ ] C: Content of port indicated by code No. C (4 bit)
[ ]: Content of data memory indicated by the content of register or data memory
[ ] P: Content of program memory (16 bit)
IC: Instruction code (6 bit)
*: Instruction having skip function
DC: Data memory column address (4 bit)
DR: Data memory row address (2 bit)
P: Wait condition select bit at WAIT instruction
Note 6: Address 000H~3FFH of program memory address: Page 0 area
Address 400H~7FFH of program memory address: Page 1 area
11 2003-06-27

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet TC9316F.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TC9316FDTS MICRO CONTROLLER CONTAINING PLL / LCD DRIVERToshiba
Toshiba
TC9316F-001DTS MICRO CONTROLLERToshiba
Toshiba
TC9316F-026DIGITAL TUNING SYSTEMToshiba
Toshiba
TC9316F-027DIGITAL TUNING SYSTEMToshiba
Toshiba

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar