|
|
Número de pieza | ZXSC400 | |
Descripción | LED DRIVER BOOST CONVERTER | |
Fabricantes | Zetex Semiconductors | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ZXSC400 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
No Preview Available ! LED DRIVER BOOST CONVERTER
ZXSC400
DESCRIPTION
The ZXSC400 is a voltage mode boost converter in the SOT23-6 package. Its low
feedback voltage allows the current in a chain of LEDs to be set and accurately
monitored with a single resistor giving minimal losses. Its excellent load and line
regulation means that for the full supply range from lithium-ion cells, the LED
current will typically change by less than 1%. Using high efficiency Zetex switching
transistors with ratings of 20V and higher allow many LEDs to be chained in series
for the best LED current matching possible.
FEATURES
• 1.8V to 8V supply range
• Typical output regulation of Ϯ1%
• Over 80% typical efficiency
• 4.5A typical shutdown current
• Series connection for ultimate LED current matching
APPLICATIONS
• White LED backlighting for colour LCD panels
• General LED backlighting
• High performance white LED flashlights
• General LED driving from batteries
PINOUT
SOT23-6
ORDERING INFORMATION
DEVICE
ZXSC400E6TA
REEL TAPE QUANTITY
SIZE WIDTH PER REEL
7“ 8mm 3000 units
DEVICE MARKING
• C400
VCC
GND
STDN
DRIVE
VFB
SENSE
Top View
ISSUE 1 - JANUARY 2003
1
1 page APPLICATIONS INFORMATION
ZXSC400
Switching transistor selection
Capacitor Selection
The choice of switching transistor has a major impact
on the converter efficiency. For optimum performance,
a bipolar transistor with low VCE(SAT) and high gain is
required. The VCEO of the switching transistor is also an
important parameter as this sees the full output
voltage when the transistor is switched off. Zetex
SuperSOT™ transistors are an ideal choice for this
application.
A small value, low ESR ceramic capacitor is required to
filter the output, typically 1F to 4.7F.
Generally an input capacitor is not required, but a small
ceramic capacitor may be added to aid EMC, typically
1F to 4.7F.
Inductor Selection
Schottky diode selection
As with the switching transistor, the Schottky rectifier
diode has a major impact on the converter efficiency. A
Schottky diode with a low forward voltage and fast
recovery time should be used for this application.
The diode should be selected so that the maximum
forward current rating is greater or equal to the
maximum peak current in the inductor, and the
maximum reverse voltage is greater or equal to the
output voltage. The Zetex ZHCS Series meet these
needs.
The inductor value must be chosen to satisfy
performance, cost and size requirements of the overall
solution.
Inductor selection has a significant impact on the
converter performance. For applications where
efficiency is critical, an inductor with a series resistance
of 250m⍀ or less should be used.
A list of recommended inductors is listed in the table
below:
Combination devices
To minimise the external component count Zetex
recommends the ZX3CDBS1M832 combination of
NPN transistor and Schottky diode in a 3mm x 2mm
MLP package. This device is recommended for use in
applications using 1 to 4 white LEDs.
The IC is also capable of driving MOSFETs. Zetex
recommends the ZXMNS3BM832 combination of low
threshold voltage N-Channel MOSFET and Schottky
diode in a 3mm x 2mm MLP package. This device is
recommended for use in applications using 1 to 8 white
LEDs.
Part No.
CMD4D11-100MC
CMD4D11-220MC
LPO2506OB-103
ST2006103
Manufacture
Sumida
Sumida
Coilcraft
Standex Electronics Inc
L
10H
22H
10H
10H
IPK (A)
0.5
0.4
1.0
0.6
RDC( )
0.457
0.676
0.24
0.1
ISSUE 1 - JANUARY 2003
5
5 Page Li - Ion to 3 LED converter
ZXSC400
100
3 White LEDs
I =20mA
90 LED
80
70
602.5 3.0 3.5 4.0
Input Voltage (V)
Input Voltage v Efficiency
30
3 White LEDs
20
10
02.5 3.0 3.5 4.0
Input Voltage (V)
Input Voltage v LED Current
Bill of Materials
Ref Value
U1
U2
L1 10H
R1 68m⍀
R2 15⍀
C1 2.2F/6V3
C2 2.2F/16V
LED
Part Number
ZXSC400
ZX3CDBS1M832
CMD4D11-100MC
LR1206 / RL1220
Generic
GRM Series
GRM Series
NSCW215
ISSUE 1 - JANUARY 2003
Manufacture
Zetex
Zetex
Sumida
IRC / Cyntec
Generic
Murata
Murata
Nichia
Comments
LED driver IC
NPN + Schottky dual
1mm height profile
1206 / 0805 size
0603 size
0805 size
1206 size
White SMT LED
11
11 Page |
Páginas | Total 16 Páginas | |
PDF Descargar | [ Datasheet ZXSC400.PDF ] |
Número de pieza | Descripción | Fabricantes |
ZXSC400 | LED DRIVER BOOST CONVERTER | Zetex Semiconductors |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |