DataSheet.es    


PDF ZNBG3110 Data sheet ( Hoja de datos )

Número de pieza ZNBG3110
Descripción FET BIAS CONTROLLER WITH POLARISATION SWITCH AND TONE DETECTION
Fabricantes Zetex Semiconductors 
Logotipo Zetex Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de ZNBG3110 (archivo pdf) en la parte inferior de esta página.


Total 16 Páginas

No Preview Available ! ZNBG3110 Hoja de datos, Descripción, Manual

FET BIAS CONTROLLER WITH POLARISATION ZNBG3110
SWITCH AND TONE DETECTION
ZNBG3111
ISSUE 2 - APRIL 1998
DEVICE DESCRIPTION
The ZNBG series of devices are designed to
meet the bias requirements of GaAs and
HEMT FETs commonly used in satellite
receiver LNBs, PMR cellular telephones etc.
with a minimum of external components.
With the addition of two capacitors and a
resistor the devices provide drain voltage and
current control for three external grounded
source FETs, generating the regulated
negative rail required for FET gate biasing
whilst operating from a single supply. This
negative bias, at -3 volts, can also be used to
supply other external circuits.
The ZNBG3110/11 includes bias circuits to
drive up to three external FETs. A control
input to the device selects either one of two
FETs as operational, the third FET is
permanently active. This feature is
particularly used as an LNB polarisation
switch. Also specific to LNB applications is
the 22KHz tone detection and logic output
feature which is used to enable high and low
band frequency switching.
Drain current setting of the ZNBG3110/11 is
user selectable over the range 0 to 15mA, this
is achieved with addition of a single resistor.
The series also offers the choice of drain
voltage to be set for the FETs, the 3110 gives
2.2 volts drain whilst the 3111 gives 2 volts.
These devices are unconditionally stable
over the full working temperature with the
FETs in place, subject to the inclusion of the
recommended gate and drain capacitors.
These ensure RF stability and minimal
injected noise.
It is possible to use less than the devices full
complement of FET bias controls, unused
drain and gate connections can be left open
circuit without affecting operation of the
remaining bias circuits.
In order to protect the external FETs the
circuits have been designed to ensure that,
under any conditions including power
up/down transients, the gate drive from the
bias circuits cannot exceed the range -3.5V
to 1V. Furthermore if the negative rail
experiences a fault condition, such as
overload or short circuit, the drain supply to
the FETs will shut down avoiding excessive
current flow.
The ZNBG3110/11 are available in QSOP20
for the minimum in device size. Device
operating temperature is -40 to 70°C to suit
a wide range of environmental conditions.
FEATURES
Provides bias for GaAs and HEMT FETs
Drives up to three FETs
Dynamic FET protection
Drain current set by external resistor
Regulated negative rail generator
requires only 2 external capacitors
Choice in drain voltage
Wide supply voltage range
Polarisation switch for LNBs
22KHz tone detection for band
switching
Compliant with ASTRA control
specifications
QSOP surface mount package
APPLICATIONS
Satellite receiver LNBs
Private mobile radio (PMR)
Cellular telephones
4-123

1 page




ZNBG3110 pdf
TEST CIRCUIT 1
ZNBG3110
ZNBG3111
TEST CIRCUIT 2
V2 Characteristics
Type
AC source
Frequency 22kHz
Voltage
350mV p/p enabled
100mV p/p disabled
V2 Characteristics
Type
AC source
Frequency 22kHz
Voltage
350mV p/p enabled
100mV p/p disabled
4-127

5 Page





ZNBG3110 arduino
APPLICATIONS CIRCUIT
ZNBG3110
ZNBG3111
APPLICATIONS INFORMATION
The above is a partial application circuit for the ZNBG series showing all external components
required for appropriate biasing. The bias circuits are unconditionally stable over the full
temperature range with the associated FETs and gate and drain capacitors in circuit.
Capacitors CD and CG ensure that residual power supply and substrate generator noise is not
allowed to affect other external circuits which may be sensitive to RF interference. They also
serve to suppress any potential RF feedthrough between stages via the ZNBG device. These
capacitors are required for all stages used. Values of 10nF and 4.7nF respectively are
recommended however this is design dependent and any value between 1nF and 100nF could
be used.
The capacitors CNB and CSUB are an integral part of the ZNBGs negative supply generator. The
negative bias voltage is generated on-chip using an internal oscillator. The required value of
capacitors CNB and CSUB is 47nF. This generator produces a low current supply of approximately
-3 volts. Although this generator is intended purely to bias the external FETs, it can be used to
power other external circuits via the CSUB pin.
Resistor RCAL sets the drain current at which all external FETs are operated. If any bias control
circuit is not required, its related drain and gate connections may be left open circuit without
affecting the operation of the remaining bias circuits.
The ZNBG devices have been designed to protect the external FETs from adverse operating
conditions. With a JFET connected to any bias circuit, the gate output voltage of the bias circuit
can not exceed the range -3.5V to 1V under any conditions, including powerup and powerdown
transients. Should the negative bias generator be shorted or overloaded so that the drain current
of the external FETs can no longer be controlled, the drain supply to FETs is shut down to avoid
damage to the FETs by excessive drain current.
4-133

11 Page







PáginasTotal 16 Páginas
PDF Descargar[ Datasheet ZNBG3110.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ZNBG3110FET BIAS CONTROLLER WITH POLARISATION SWITCH AND TONE DETECTIONZetex Semiconductors
Zetex Semiconductors
ZNBG3111FET BIAS CONTROLLER WITH POLARISATION SWITCH AND TONE DETECTIONZetex Semiconductors
Zetex Semiconductors
ZNBG3113FET BIAS CONTROLLER WITH POLARISATION SWITCH AND TONE DETECTIONZetex Semiconductors
Zetex Semiconductors
ZNBG3114FET BIAS CONTROLLER WITH POLARISATION SWITCH AND TONE DETECTIONZetex Semiconductors
Zetex Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar