DataSheet.es    


PDF PCA9546PW Data sheet ( Hoja de datos )

Número de pieza PCA9546PW
Descripción 4-channel I2C switch with reset
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de PCA9546PW (archivo pdf) en la parte inferior de esta página.


Total 17 Páginas

No Preview Available ! PCA9546PW Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
PCA9546
4-channel I2C switch with reset
Product data sheet
Supersedes data of 2002 Feb 19
2004 Sep 30
Philips
Semiconductors

1 page




PCA9546PW pdf
Philips Semiconductors
4-channel I2C switch with reset
Product data sheet
PCA9546
DEVICE ADDRESSING
Following a START condition the bus master must output the
address of the slave it is accessing. The address of the PCA9546 is
shown in Figure 3. To conserve power, no internal pull-up resistors
are incorporated on the hardware selectable address pins and they
must be pulled HIGH or LOW.
1 1 1 0 A2 A1 A0 R/W
FIXED
HARDWARE SELECTABLE
SW00915
Figure 3. Slave address
The last bit of the slave address defines the operation to be
performed. When set to logic 1, a read is selected while a logic 0
selects a write operation.
CONTROL REGISTER
Following the successful acknowledgement of the slave address,
the bus master will send a byte to the PCA9546, which will be stored
in the control register. If multiple bytes are received by the
PCA9546, it will save the last byte received. This register can be
written and read via the I2C-bus.
CHANNEL SELECTION BITS
(READ/WRITE)
7 65 4 3 21 0
X X X X B3 B2 B1 B0
CHANNEL 0
CHANNEL 1
CHANNEL 2
CHANNEL 3
Figure 4. Control register
SW01026
CONTROL REGISTER DEFINITION
One or several SCx/SDx downstream pair, or channel, is selected
by the contents of the control register. This register is written after
the PCA9546 has been addressed. The 2 LSBs of the control byte
are used to determine which channel is to be selected. When a
channel is selected, the channel will become active after a stop
condition has been placed on the I2C-bus. This ensures that all
SCx/SDx lines will be in a HIGH state when the channel is made
active, so that no false conditions are generated at the time of
connection.
Table 1. Control Register; Write — Channel Selection/
Read — Channel Status
D7 D6 D5 D4 B3 B2 B1 B0 COMMAND
0
Channel 0
disabled
XXXXXXX
1
Channel 0
enabled
0
Channel 1
disabled
XXXXXX
X
1
Channel 1
enabled
0
Channel 2
disabled
XXXXX
XX
1
Channel 2
enabled
0
Channel 3
disabled
XXXX
XXX
1
Channel 3
enabled
No channel
0
0
0
0
0
0
0
0
selected;
power-up/reset
default state
NOTE: Several channels can be enabled at the same time.
Ex: B3 = 0, B2 = 1, B1 = 1, B0 = 0, means that channel 0 and 3 are
disabled and channel 1 and 2 are enabled.
Care should be taken not to exceed the maximum bus capacity.
RESET INPUT
The RESET input is an active-LOW signal which may be used to
recover from a bus fault condition. By asserting this signal LOW for
a minimum of tWL, the PCA9546 will reset its registers and I2C state
machine and will deselect all channels. The RESET input must be
connected to VDD through a pull-up resistor.
POWER-ON RESET
When power is applied to VDD, an internal Power On Reset holds
the PCA9546 in a reset state until VDD has reached VPOR. At this
point, the reset condition is released and the PCA9546 registers and
I2C state machine are initialized to their default states, all zeroes
causing all the channels to be deselected.
2004 Sep 30
5

5 Page





PCA9546PW arduino
Philips Semiconductors
4-channel I2C switch with reset
Product data sheet
PCA9546
DC CHARACTERISTICS
VDD = 3.6 V to 5.5 V; VSS = 0 V; Tamb = –40 °C to +85 °C; unless otherwise specified. (See page 10 for VDD = 2.3 V to 3.6 V)
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
MIN TYP MAX
Supply
VDD Supply voltage
IDD Supply current
Istb Standby current
VPOR
Power-on reset voltage
Input SCL; input/output SDA
Operating mode; VDD = 5.5 V;
no load; VI = VDD or VSS;
fSCL = 100 kHz
Standby mode; VDD = 5.5 V;
no load; VI = VDD or VSS
no load; VI = VDD or VSS
3.6 — 5.5
— 570 600
— 250 300
— 1.7 2.1
VIL LOW-level input voltage
VIH HIGH-level input voltage
IOL LOW-level output current
IIL LOW-level input current
IIH HIGH-level input current
Ci Input capacitance
Select inputs A0 to A2 / RESET
VOL = 0.4 V
VOL = 0.6 V
VI = VSS
VI = VDD
VI = VSS
–0.5
— 0.3VDD
0.7VDD
6
3 ——
6 ——
–10 — +10
— — 100
— 12 13
VIL
VIH
ILI
Ci
Pass Gate
LOW-level input voltage
HIGH-level input voltage
Input leakage current
Input capacitance
pin at VDD or VSS
VI = VSS
–0.5
0.7VDD
–1
— +0.3VDD
— VDD + 0.5
— +50
23
RON
VPass
IL
Cio
Switch resistance
Switch output voltage
Leakage current
Input/output capacitance
VCC = 4.5 V to 5.5 V; VO = 0.4 V; IO = 15 mA
Vswin = VDD = 5.0 V; Iswout = –100 µA
Vswin = VDD = 4.5 V to 5.5 V; Iswout = –100 µA
VI = VDD or VSS
VI = VSS
4
2.6
–10
11 24
3.5 —
— 4.5
— +100
35
UNIT
V
µA
µA
V
V
V
mA
mA
µA
µA
pF
V
V
µA
pF
V
V
µA
pF
2004 Sep 30
11

11 Page







PáginasTotal 17 Páginas
PDF Descargar[ Datasheet PCA9546PW.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
PCA9546PW4-channel I2C switch with resetNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar