DataSheet.es    


PDF PCA80C51BH-3P Data sheet ( Hoja de datos )

Número de pieza PCA80C51BH-3P
Descripción CMOS single-chip 8-bit microcontrollers
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de PCA80C51BH-3P (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! PCA80C51BH-3P Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
Product specification
IC20 Data Handbook
1996 Aug 16
Philips
Semiconductors

1 page




PCA80C51BH-3P pdf
Philips Semiconductors
CMOS single-chip 8-bit microcontrollers
Product specification
80C31/80C51/87C51
ORDERING INFORMATION (Continued)
ROMless
(ORDER NUMBER)
ROMless
(MARKING NUMBER)
ROM
PHILIPS
DRAWING
NUMBER
TEMPERATURE RANGE oC
AND PACKAGE1
Freq
MHz
PCB80C31-2 N
PCB80C31-2 A
PCB80C31BH2-12P PCB80C51BH-2P SOT129-1 0 to +70, Plastic Dual In-line Package, OTP
PCB80C31BH2-12WP PCB80C51BH-2WP SOT187-2 0 to +70, Plastic Leaded Chip Carrier, OTP
PCB80C31BH2-12H PCB80C51BH-2H SOT307-22 0 to +70, Plastic Quad Flat Pack, OTP
0.5 to 12
0.5 to 12
0.5 to 12
PCB80C31-3 N
PCB80C31-3 A
PCB80C31BH3-16P PCB80C51BH-3P SOT129-1 0 to +70, Plastic Dual In-line Package, OTP
PCB80C31BH3-16WP PCB80C51BH-3WP SOT187-2 0 to +70, Plastic Leaded Chip Carrier, OTP
PCB80C31BH3-16H PCB80C51BH-3H SOT307-22 0 to +70, Plastic Quad Flat Pack, OTP
1.2 to 16
1.2 to 16
1.2 to 16
PCF80C31-3 N
PCF80C31-3 A
PCF80C31BH3-16P PCF80C51BH-3P SOT129-1 –40 to +85, Plastic Dual In-line Package, OTP
PCF80C31BH3-16WP PCF80C51BH-3WP SOT187-2 –40 to +85, Plastic Leaded Chip Carrier, OTP
PCF80C31BH3-16H PCF80C51BH-3H SOT307-22 –40 to +85, Plastic Quad Flat Pack, OTP
PCA80C31BH3-16P PCA80C51BH-3P SOT129-1 –40 to +125, Plastic Dual In-line Package
PCA80C31BH3-16WP PCA80C51BH-3WP SOT187-2 –40 to +125, Plastic Leaded Chip Carrier
1.2 to 16
1.2 to 16
1.2 to 16
1.2 to 16
1.2 to 16
PCB80C31-4 N
PCB80C31-4 A
PCB80C31BH4-24P PCB80C51BH-4P SOT129-1 0 to +70, Plastic Dual In-line Package, OTP
PCB80C31BH4-24WP PCB80C51BH-4WP SOT187-2 0 to +70, Plastic Leaded Chip Carrier, OTP
PCB80C31BH4-24H PCB80C51BH-4H SOT307-22 0 to +70, Plastic Quad Flat Pack, OTP
1.2 to 24
1.2 to 24
1.2 to 24
PCF80C31-4 N
PCF80C31-4 A
PCF80C31BH4-24P PCF80C51BH-4P SOT129-1 –40 to +85, Plastic Dual In-line Package, OTP
PCF80C31BH4-24WP PCF80C51BH-4WP SOT187-2 –40 to +85, Plastic Leaded Chip Carrier, OTP
PCF80C31BH4-24H PCF80C51BH-4H SOT307-22 –40 to +85, Plastic Leaded Chip Carrier, OTP
1.2 to 24
1.2 to 24
1.2 to 24
PCB80C31-5 N
PCB80C31-5 A
PCB80C31-5 B
PCB80C31BH5-30P PCB80C51BH-5P SOT129-1 0 to +70, Plastic Dual In-line Package
PCB80C31BH5-30WP PCB80C51BH-5WP SOT187-2 0 to +70, Plastic Leaded Chip Carrier
PCB80C31BH5-30H PCB80C51BH-5H SOT307-22 0 to +70, Plastic Quad Flat Pack
1.2 to 33
1.2 to 33
1.2 to 33
1996 Aug 16
5

5 Page





PCA80C51BH-3P arduino
Philips Semiconductors
CMOS single-chip 8-bit microcontrollers
Product specification
80C31/80C51/87C51
DC ELECTRICAL CHARACTERISTICS
Tamb = 0°C to +70°C or –40°C to +85°C, VCC = 5V ±20%, VSS = 0V (PCB80C31/51 and PCF80C31/51) (12, 16, and 24MHz versions)
Tamb = 0°C to +70°C or –40°C to +85°C, VCC = 5V ±10%, VSS = 0V (87C51 12, 16, and 24MHz versions) (PCB80C31/51 33MHz version);
For SC87C51 (33MHz only) Tamb = 0°C to +70°C, VCC = 5V ±5%
TEST
LIMITS
SYMBOL
PARAMETER
CONDITIONS
MIN
TYPICAL1
MAX
UNIT
VIL
VIL1
VIH
VIH1
VOL
VOL1
VOH
Input low voltage, except EA7
Input low voltage to EA7
Input high voltage, except XTAL1, RST7
Input high voltage, XTAL1, RST7
Output low voltage, ports 1, 2, 311
Output low voltage, port 0, ALE, PSEN11
Output high voltage, ports 1, 2, 3, ALE, PSEN3
IOL = 1.6mA2
IOL = 3.2mA2
IOH = –60µA,
IOH = –25µA
IOH = –10µA
–0.5
0
0.2VCC+0.9
0.7VCC
2.4
0.75VCC
0.9VCC
0.2VCC–0.1
0.2VCC–0.3
VCC+0.5
VCC+0.5
0.45
0.45
V
V
V
V
V
V
V
V
V
VOH1
Output high voltage (port 0 in external bus mode)
IOH = –800µA,
IOH = –300µA
IOH = –80µA
2.4
0.75VCC
0.9VCC
V
V
V
IIL Logical 0 input current, ports 1, 2, 37
ITL Logical 1-to-0 transition current, ports 1, 2, 37
VIN = 0.45V
See note 4
–50
–650
µA
µA
ILI Input leakage current, port 0
VIN = VIL or VIH
ICC Power supply current:7
Active mode @ 12MHz8 (Philips)
See note 6
Active mode @ 12MHz5 (Philips North America)
Idle mode @ 12MHz9 (Philips)
Idle mode @ 12MHz (Philips North America)
Power-down mode10 (Philips and
Philips North America)
±10 µA
18 mA
11.5 19 mA
4.4 mA
1.3 4 mA
3 50 µA
RRST
Internal reset pull-down resistor
(Philips North America)
(Philips)
50 300 k
50 150 k
CIO Pin capacitance12
10 pF
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V.
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the VOLs of ALE and ports 1 and 3. The noise is due
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. IOL can exceed these conditions provided that no
single output sinks more than 5mA and no more than two outputs exceed the test conditions.
3. Capacitive loading on ports 0 and 2 may cause the VOH on ALE and PSEN to momentarily fall below the 0.9VCC specification when the
address bits are stabilizing.
4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when VIN is approximately 2V.
5. ICCMAX at other frequencies (for Philips North America parts) is given by: Active mode: ICCMAX = 1.43 X FREQ + 1.90;
Idle mode: ICCMAX = 0.14 X FREQ +2.31, where FREQ is the external oscillator frequency in MHz. ICCMAX is given in mA. See Figure 8.
6. See Figures 9 through 12 for ICC test conditions.
7. For Philips North America parts when Tamb = –40°C to +85°C or Philips parts when Tamb = –40°C to +125°C, see DC Electrical
Characteristics table on previous page.
8. The operating supply current is measured with all output pins disconnected; XTAL1 driven with tr = tf = 10ns; VIL = VSS + 0.5V;
VIH = VCC – 0.5V; XTAL2 not connected; EA = RST = Port 0 = VCC.
9. The idle mode supply current is measured with all output pins disconnected; XTAL1 driven with tr = tf = 10ns; VIL = VSS + 0.5V;
VIH = VCC – 0.5V; XTAL2 not connected; EA = Port 0 = VCC; RST = VSS.
10. The power-down current is measured with all output pins disconnected, XTAL2 not connected, EA = Port 0 = VCC; RST = VSS.
11. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin:
15mA
Maximum IOL per 8-bit port:
26mA
Maximum IOL total for all outputs:
67mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
12. Pin capacitance for the ceramic DIP package is 15pF maximum.
1996 Aug 16
11

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet PCA80C51BH-3P.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
PCA80C51BH-3PCMOS single-chip 8-bit microcontrollersNXP Semiconductors
NXP Semiconductors
PCA80C51BH-3WPCMOS single-chip 8-bit microcontrollersNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar