DataSheet.es    


PDF P82C150 Data sheet ( Hoja de datos )

Número de pieza P82C150
Descripción CAN Serial Linked I/O device SLIO with digital and analog port functions
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de P82C150 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! P82C150 Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
DATA SHEET
P82C150
CAN Serial Linked I/O device
(SLIO) with digital and analog port
functions
Preliminary specification
Supersedes data of 1995 Oct 11
File under Integrated Circuits, IC18
1996 Jun 19

1 page




P82C150 pdf
Philips Semiconductors
CAN Serial Linked I/O device (SLIO) with
digital and analog port functions
5 FUNCTIONAL DIAGRAM
Preliminary specification
P82C150
handbook, full pagewidth
RX0
CAN-bus inputs
RX1
reference
REF
voltage output
TX1
CAN-bus outputs
TX0
RST (reset)
XMOD
VDD
AVDD
P16
ADC feedback output
P82C150
P15 analog-to-digital
comparator input
P14 multiplexed analog-
to-digital signal
P13 analog
input
P12
comparator
P11 inputs
P10 DPM1
output
P9
P8
P7 analog inputs,
analog switches
P6
P5
P4 DPM2
output
P3
P2
identifier
P1 programming
P0/CLK
16-bit
digital I/O
VSS
AVSS
MHA066
1996 Jun 19
Fig.2 Functional diagram.
5

5 Page





P82C150 arduino
Philips Semiconductors
CAN Serial Linked I/O device (SLIO) with
digital and analog port functions
Preliminary specification
P82C150
7.2.6 ANALOG CONFIGURATION REGISTER (ADDRESS 5)
This read/write register contains the bits ADC, OC3 to
OC1, M3 to M1 and SW3 to SW1 (see Fig.7).
ADC bit (analog-to-digital conversion start bit; write only
bit). The P82C150 starts an analog-to-digital conversion
cycle at ADC = 1 ended with the transmission of a
message containing the result. After that, the ADC bit is
reset automatically.
OC3 to OC1 bits (comparator output data; read only
bits). The bits OC3 to OC1 represent the logical output
level of the analog comparators at input port pins P10,
P11, P12, P13 and P15. The P82C150 sends back the
logical output value of these comparators after having
received a Data Frame (see Section 7.3.3) addressing
the Analog Configuration Register. The comparator
outputs can be monitored at the output port pins P8, P9
and P7.
M3 to M1 bits (multiplexer control bits; write only bits).
The logical value of the comparators is monitored on
port pins P8, P9 and P7 (see Fig.7) by setting M3 to M1
to logic 1, provided that these pins are configured as
outputs (OE = 1). Additionally the register content is
sent automatically when the corresponding port bits in
the Positive Edge Register and/or Negative Edge
Register and the corresponding bits in the Output
Enable Register are set.
SW3 to SW1 (analog switch control bits; write only bits).
One of the analog switches S1 to S6 can be closed by
setting the switch bits to the corresponding value
(see Fig.7 and Table 4).
7.2.7 DPM1 REGISTER (ADDRESS 6)
This write only register contains data for a quasi-analog
output signal on port pin P10, which is generated by
Distributed Pulse Modulation (DPM; see Fig.9).
The Output Enable bit must be set for this functions
(OE10 = 1). The DPM1 output signal is inverted by setting
DO10 = 1. The number of output pulses during a DPM
period is given by the DPM1 Register value. These pulses
have 4 × tCLK length and are distributed over the DPM
period. An analog voltage is provided after smoothing the
output signal by an external RC combination.
7.2.8 DPM2 REGISTER (ADDRESS 7)
This write only register contains data for a quasi-analog
output signal on port pin P4. The function of the DPM2
corresponds to the definition of DPM1.
7.2.9
ANALOG-TO-DIGITAL CONVERSION (ADC)
REGISTER (ADDRESS 8)
This read only register contains the result of the
analog-to-digital converted level of that I/O pin which was
selected by the SW bits. The conversion is started by
ADC-bit set to logic 1 (see Section 7.2.6), or by
transmitting a Data Frame addressing the ADC Register.
Table 4 Analog switch selection by SW3, SW2, SW1.
SW3
0
0
0
0
1
1
1
1
SW2
0
0
1
1
0
0
1
1
SW1
0
1
0
1
0
1
0
1
SWITCH STATE
no switch closed (S0); note 1
S1 closed
S2 closed
S3 closed
S4 closed
S5 closed
S6 closed
reserved
Note
1. Evidently if P14 is driven, it may not be connected to
any other driven pin via the internal analog switches
(avoid short-circuit!).
1996 Jun 19
11

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet P82C150.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
P82C150CAN Serial Linked I/O device SLIO with digital and analog port functionsNXP Semiconductors
NXP Semiconductors
P82C150AFTCAN Serial Linked I/O device SLIO with digital and analog port functionsNXP Semiconductors
NXP Semiconductors
P82C150AHTCAN Serial Linked I/O device SLIO with digital and analog port functionsNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar