DataSheet.es    


PDF TDA8567 Data sheet ( Hoja de datos )

Número de pieza TDA8567
Descripción 4 x 25 W BTL quad car radio power amplifier
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de TDA8567 (archivo pdf) en la parte inferior de esta página.


Total 20 Páginas

No Preview Available ! TDA8567 Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
DATA SHEET
TDA8567Q
4 × 25 W BTL quad car radio power
amplifier
Product specification
Supersedes data of 1997 Feb 12
File under Integrated Circuits, IC01
1998 Sep 23

1 page




TDA8567 pdf
Philips Semiconductors
4 × 25 W BTL quad car radio power
amplifier
Product specification
TDA8567Q
FUNCTIONAL DESCRIPTION
The TDA8567Q contains four identical amplifiers which
can be used for bridge applications. The gain of each
amplifier is fixed at 26 dB.
Mode select switch (pin 15)
Standby: low supply current (<100 µA)
Mute: input signal suppressed
Operating: normal on condition.
Since this pin has a low input current (<80 µA), a low cost
supply switch can be applied.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during 150 ms (charging of the input
capacitors at pins 10, 11, 13 and 14). When switching
from standby to mute, the slope should be at least 18 V/s.
This can be realized by:
Microprocessor control
External timing circuit (see Fig.3).
SHORT-CIRCUIT DIAGNOSTIC
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
10 ms after removal of the short-circuit. During this
short-circuit condition, pin 9 is continuously LOW.
When a short-circuit occurs across the load of one or more
channels, the output stages are switched off during
approximately 10 ms. After that time it is checked during
approximately 50 µs to determine whether the short-circuit
is still present.
Due to this duty cycle of 50 µs/10 ms the average current
consumption during this short-circuit condition is very low.
During this short-circuit condition, pin 9 is LOW for 10 ms
and HIGH for 50 µs (see Fig.5). The protection circuits of
all channels are coupled. This means that if a short-circuit
condition occurs in one of the channels, all channels are
switched off. Consequently, the power dissipation in any
short-circuit condition is very low.
Diagnostic output (pin 9)
DYNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 9
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and so limit the distortion. The output level of pin 9
is independent of the number of channels that are clipping
(see Fig.4).
TEMPERATURE PRE-WARNING
When the virtual junction temperature Tvj reaches 145 °C,
pin 9 goes LOW.
OPEN COLLECTOR OUTPUTS
The diagnostic pin has an open collector output, so more
devices can be tied together. An external pull-up resistor is
needed.
handbook, halfpa+geVP
10 k
MODE
BZX79C/3.9V
47 µF
MGD959
Fig.3 Mode select switch circuitry.
1998 Sep 23
handbook, halfpVagoe
0
MGG155
V9
VP
0
t
Fig.4 Distortion detector waveform.
5

5 Page





TDA8567 arduino
Philips Semiconductors
4 × 25 W BTL quad car radio power
amplifier
Product specification
TDA8567Q
Test information
Figures 8 to 13 have the following conditions: VP = 14.4 V; RL = 4 ; f = 1 kHz; 80 kHz filter used; unless otherwise
specified.
handboo3k,0h0alfpage
IP
(mA)
200
100
MGD921
handbook,6h0alfpage
Po
(W)
40
20
MGD922
(1)
(2)
(3)
0
04
8 12 16 20
VP (V)
Fig.8 IP as a function of VP.
0
8 10 12 14 16 18
VP (V)
(1) EIAJ.
(2) 10%.
(3) 0.5%.
Fig.9 Po as a function of VP.
10
handbook, halfpage
THD+N
(%)
1
MGD923
101
102
10
f = 10 kHz
1 kHz
100 Hz
102 103 104 105
Po (W)
10
handbook, halfpage
THD+N
(%)
1
MGD924
101
102
10
10 W
1W
102
103
104 105
f (Hz)
Fig.10 THD + N as a function of Po.
1998 Sep 23
Fig.11 THD + N as a function of frequency.
11

11 Page







PáginasTotal 20 Páginas
PDF Descargar[ Datasheet TDA8567.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TDA85602 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facilityNXP Semiconductors
NXP Semiconductors
TDA8560Q2 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facilityNXP Semiconductors
NXP Semiconductors
TDA85612 x 24 W BTL or 4 x 12 W single-ended car radio power amplifierNXP Semiconductors
NXP Semiconductors
TDA8561Q2 x 24 W BTL or 4 x 12 W single-ended car radio power amplifierNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar