|
|
PDF TDA8547 Data sheet ( Hoja de datos )
| Número de pieza | TDA8547 | |
| Descripción | 2 x 1 W BTL audio amplifier with output channel switching | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA8547 (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA8547
2 × 1 W BTL audio amplifier with
output channel switching
Preliminary specification
File under Integrated Circuits, IC01
1997 Oct 07
1 page  
Philips Semiconductors
2 × 1 W BTL audio amplifier with output
channel switching
Preliminary specification
TDA8547
operate and the power amplifier of channel 2 will be in the
standby mode. In this case only the loudspeaker at
channel 1 can operate and the loudspeaker at channel 2
will be switched off. Setting the SELECT pin to a LOW or
a HIGH voltage results in a reduction of quiescent current
consumption by a factor of approximately 2.
Switching with the SELECT pin during operating is not
plop-free, because the input capacitor of the channel
which is coming out of standby needs to be charged first.
For plop-free channel selecting the device has first to be
set in mute condition with the MODE pin (between 1.5 V
and VCC − 1.5 V), then set the SELECT pin to the new
level, after a delay set the MODE pin to a LOW level.
The delay needed depends on the values of the input
capacitor and the feedback resistors. Time needed is
approx. 10 × C1 × (R1 + R2), so approximately 0.6 s. for
the values in Fig.4.
Table 1 Control pins MODE and SELECT versus status of output channels
Voltage levels at control pins at VP = 5 V; for other supply voltages see Figs. 14 and 15.
CONTROL PIN
STATUS OF OUTPUT CHANNEL
MODE
HIGH(1)/NC(2)
HVP(4)
LOW(5)
HVP(4)/LOW(5)
HVP(4)/LOW(5)
HVP(4)/LOW(5)
SELECT
X(3)
HVP(4)/NC(2)
HVP(4)/NC(2)
HIGH(1)
HVP(4)/NC(2)
LOW(5)
CHANNEL 1
standby
mute
on
mute/on
mute/on
standby
CHANNEL 2
standby
mute
on
standby
mute/on
mute/on
Notes
1. HIGH = Vpin > VCC − 0.5 V.
2. NC = not connected or floating.
3. X = don’t care.
4. HVP = 1.5 V < Vpin < VCC − 1.5 V.
5. LOW = Vpin < 0.5 V.
TYP. Iq
(mA)
0
15
15
8
15
8
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
VCC
VI
IORM
Tstg
Tamb
VPsc
Ptot
supply voltage
input voltage
repetitive peak output current
storage temperature
operating ambient temperature
AC and DC short-circuit safe voltage
total power dissipation
CONDITIONS
operating
SO16
DIP16
MIN.
−0.3
−0.3
−
−55
−40
−
−
−
MAX.
+18
VCC + 0.3
1
+150
+85
10
1.2
2.2
UNIT
V
V
A
°C
°C
V
W
W
QUALITY SPECIFICATION
In accordance with “SNW-FQ-611-E”. The number of the quality specification can be found in the “Quality Reference
Handbook”. The handbook can be ordered using the code 9397 750 00192.
1997 Oct 07
5
5 Page 
Philips Semiconductors
2 × 1 W BTL audio amplifier with output
channel switching
Preliminary specification
TDA8547
10
handbook, halfpage
THD
(%)
1
10−1
MGD892
(1)
(2)
10−2
10 102 103 104 105
f (Hz)
Po = 0.5 W; Gv = 20 dB.
(1) VCC = 5 V; RL = 8 Ω.
(2) VCC = 9 V; RL = 16 Ω.
Fig.7 THD as a function of frequency.
handbook−,6h0alfpage
αcs
(dB)
−70
−80
−90
MGK699
(1)
(2)
(3)
−100
10
102 103
VCC = 5 V; Vo = 2 V; RL = 8 Ω.
(1) Gv = 30 dB.
(2) Gv = 20 dB.
(3) Gv = 6 dB.
104 f (Hz) 105
Fig.8 Channel separation as a function of
frequency.
handbook−,2h0alfpage
SVRR
(dB)
−40
−60
MGD894
(1)
(2)
(3)
−80
10 102 103
VCC = 5 V; RS = 0 Ω; Vr = 100 mV.
(1) Gv = 30 dB.
(2) Gv = 20 dB.
(3) Gv = 6 dB.
104 105
f (Hz)
Fig.9 SVRR as a function of frequency.
1997 Oct 07
handbook2, .h5alfpage
Po
(W)
2
1.5
MGD895
(1) (2)
1
0.5
0
0 4 8 12
VCC (V)
THD = 10%.
(1) RL = 8 Ω.
(2) RL = 16 Ω.
Fig.10 Po as a function of VCC.
11
11 Page | ||
| Páginas | Total 24 Páginas | |
| PDF Descargar | [ Datasheet TDA8547.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA8540 | 4 X 4 video switch matrix | NXP Semiconductors |
| TDA8541 | 1 W BTL audio amplifier | NXP Semiconductors |
| TDA8542 | 2 x 1 W BTL audio amplifier | NXP Semiconductors |
| TDA8542AT | 2 x 1.5 W BTL audio amplifier | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |