|
|
PDF TDA8501T Data sheet ( Hoja de datos )
| Número de pieza | TDA8501T | |
| Descripción | PAL/NTSC encoder | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA8501T (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA8501
PAL/NTSC encoder
Preliminary specification
File under Integrated Circuits, IC02
April 1993
1 page  
Philips Semiconductors
PAL/NTSC encoder
Preliminary specification
TDA8501
SYMBOL
PIN
DESCRIPTION
PAL/NTSC and
Y/Y + SYNC
NOTCH
Y +SYNC OUT
Y +SYNC IN
BURST ADJ
Y +SYNC OUT
OSC
CS
17 four level control pin (note 2)
18 Y +SYNC output via an internal resistor of 2 kΩ; a notch filter can be connected to this pin
19 2 V (p-p) nominal Y +SYNC output
20 Y +SYNC input; (from pin 22) connected to the output of the external delay line
21 burst current adjustment via external resistor
22 Y +SYNC output 1 V (p-p) nominal, connected to the input of the external delay line
23 oscillator tuning: connected to either a crystal in series with capacitor to ground, or to an
external frequency source via a resistor in series with a capacitor
24 composite sync input, 0.3 V (p-p) nominal
Notes
1. Pin 4: in PAL mode, if not connected to external H2 pulse, this pin is the output for the internally generated H/2 signal.
Pin 4: in NTSC mode, for internal set-up this pin is connected to ground; when internal set-up is switched off, this pin
is connected to VCC.
2. The listed voltages connected to pin 17 (if VCC = + 5 V) enable the following Y (via pin 5) input signal states:
0 V = PAL mode; at pin 5, Y without sync and input blanking on
5 V = NTSC mode; at pin 5, Y without sync and input blanking on
1.8 V = PAL mode; at pin 5, Y with sync and input blanking off
3.2 V = NTSC mode; at pin 5, Y with sync and input blanking off
April 1993
5
5 Page 
Philips Semiconductors
PAL/NTSC encoder
Preliminary specification
TDA8501
Oscillator and Filter Control
The internal crystal oscillator is connected to pin 23 which
provides for the external connection of a crystal in series
with a trimmer to ground. It is possible to connect an
external signal source to pin 23, via a capacitor in series
with a resistor. The signal shape is not important.
Figure 11 shows the external components connected to
pin 23 and the required conditions. The minimum AC
current of 50 µA must be determined by the resistors
(Rint and Rext) and the voltage of the signal source. For
example, in this way an external sub-carrier, locked to the
sync, can be used.
PAL mode:
NTSC mode:
frequency of the oscillator is
4.433618 MHz.
frequency of the oscillator is
3.579545 MHz.
The −3 dB of the low pass filters and the centre frequency
of the bandpass filter are controlled by the filter control
loop and directly coupled to the value of the frequency of
the oscillator. The external capacitor of the control loop is
connected to pin 15.
Sync separator and Pulse shaper
The composite sync (CS) input at pin 24 (via the sync
separator) together with a sawtooth generator provide the
source for all pulses necessary for the processing.
Pulses are used for:
• clamping
• video blanking
• H/2
• chrominance blanking
• burst pulse generation for adding to U, V
• pulses for the modulator offset control.
The value of the sawtooth generator output (current) is
determined by the value of a fixed resistor to ground which
is connected externally at pin 21 (BURST ADJ). When
finer tolerance of the burst position is required, the fixed
resistor is connected in series with a variable
potentiometer to ground. By use of the potentiometer the
burst position at the outputs can be finely adjusted, after
which the pulse width of the burst and the position and
pulse width of all other internal pulses are then
determined. When using a fixed resistor with a tolerance of
2%, a tolerance of 10% of the burst position can be
expected. Timing diagrams of the pulses are provided by
Figs 12 and 13.
H/2 at pin 4 is only necessary in the PAL mode when the
internal H/2 pulse requires locking with an external H/2
phase (two or more encoders locked in same phase). The
forcing of the internal H/2 to a desired phase is possible by
means of an external pulse. Forcing is active at HIGH
level.
For the functioning of Pin 4 in the NTSC mode see also
section Black and Blanking levels in PAL and NTSC
modes.
Fig.11 Tuning circuit for external signal source.
April 1993
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet TDA8501T.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA8501 | PAL/NTSC encoder | NXP Semiconductors |
| TDA8501T | PAL/NTSC encoder | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |