DataSheet.es    


PDF TDA8042M Data sheet ( Hoja de datos )

Número de pieza TDA8042M
Descripción Quadrature demodulator
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de TDA8042M (archivo pdf) en la parte inferior de esta página.


Total 16 Páginas

No Preview Available ! TDA8042M Hoja de datos, Descripción, Manual

INTEGRATED CIRCUITS
DATA SHEET
TDA8042M
Quadrature demodulator
Product specification
File under Integrated Circuits, IC02
1997 Apr 11

1 page




TDA8042M pdf
Philips Semiconductors
Quadrature demodulator
Product specification
TDA8042M
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
VCC
Vi
Ptot
Tstg
Tj
Tamb
supply voltage
input voltage on all pins
total power dissipation
IC storage temperature
junction temperature
operating ambient temperature
MIN.
0.3
0.3
55
0
MAX.
+6.0
VCC
470
+150
+150
+70(1)
UNIT
V
V
mW
°C
°C
°C
Note
1. The operating ambient temperature can be extended up to +85 °C providing the supply voltage remains lower or
equal to 5.2 V in order to maintain the junction temperature below 150 °C.
QUALITY SPECIFICATION
All pins withstand the ESD test in accordance with “UZW-BO/FQ-A302 (human body model)” and with
“UZW-BO/FQ-B302 (machine model)”. These numbers can be found in the “Quality reference Handbook”. The handbook
can be ordered using the code 9397 750 00192.
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
Rth j-a
thermal resistance from junction to ambient in free air
VALUE
120
UNIT
K/W
1997 Apr 11
5

5 Page





TDA8042M arduino
Philips Semiconductors
Quadrature demodulator
Product specification
TDA8042M
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SSOP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
Wave soldering
Wave soldering is not recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
1997 Apr 11
11

11 Page







PáginasTotal 16 Páginas
PDF Descargar[ Datasheet TDA8042M.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TDA8042MQuadrature demodulatorNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar