DataSheet.es    


PDF V29C51000B Data sheet ( Hoja de datos )

Número de pieza V29C51000B
Descripción 512K BIT 65/536 x 8 BIT 5 VOLT CMOS FLASH MEMORY
Fabricantes Mosel Vitelic Corp 
Logotipo Mosel Vitelic  Corp Logotipo



Hay una vista previa y un enlace de descarga de V29C51000B (archivo pdf) en la parte inferior de esta página.


Total 16 Páginas

No Preview Available ! V29C51000B Hoja de datos, Descripción, Manual

MOSEL VITELIC
V29C51000T/V29C51000B
512K BIT (65,536 x 8 BIT)
5 VOLT CMOS FLASH MEMORY
PRELIMINARY
Features
s 64Kx8-bit Organization
s Address Access Time: 45, 70, 90 ns
s Single 5V ± 10% Power Supply
s Sector Erase Mode Operation
s 8KB Boot Block (lockable)
s 512 bytes per Sector, 128 Sectors
– Sector-Erase Cycle Time: 10ms (Max)
– Byte-Program Cycle Time: 20µs (Max)
s Minimum 10,000 Erase-Program Cycles
s Low power dissipation
– Active Read Current: 20mA (Typ)
– Active Program Current: 30mA (Typ)
– Standby Current: 100µA (Max)
s Hardware Data Protection
s Low VCC Program Inhibit Below 3.2V
s Self-timed program/erase operations with end-
of-cycle detection
– DATA Polling
– Toggle Bit
s CMOS and TTL Interface
s Available in two versions
– V29C51000T (Top Boot Block)
– V29C51000B (Bottom Boot Block)
s Packages:
– 32-pin Plastic DIP
– 32-pin TSOP-I
– 32-pin PLCC
Description
The V29C51000T/V29C51000B is a high speed
65,536 x 8 bit CMOS flash memory. Programming
or erasing the device is done with a single 5 Volt
power supply. The device has separate chip enable
CE, program enable WE, and output enable OE
controls to eliminate bus contention.
The V29C51000T/V29C51000B offers a combi-
nation of features: Boot Block with Sector Erase
Mode. The end of program/erase cycle is detected
by DATA Polling of I/O7 or by the Toggle Bit I/O6.
The V29C51000T/V29C51000B features a
sector erase operation which allows each sector to
be erased and reprogrammed without affecting
data stored in other sectors. The device also
supports full chip erase.
Boot block architecture enables the device to
boot from either the top (V29C51000T) or bottom
(V29C51000B) sector. All inputs and outputs are
CMOS and TTL compatible.
The V29C51000T/V29C51000B is ideal for
applications that require updatable code and data
storage.
Device Usage Chart
Operating
Temperature
Range
0°C to 70°C
Package Outline
PTJ
•••
Access Time (ns)
45 70 90
•••
Temperature
Mark
Blank
V29C51000T/V29C51000B Rev. 0.5 October 2000
1

1 page




V29C51000B pdf
MOSEL VITELIC
V29C51000T/V29C51000B
AC Electrical Characteristics
(over all temperature ranges)
Read Cycle
Parameter
Name
tRC
tAA
tACS
tOE
tCLZ
tOLZ
tDF
tOH
Parameter
Read Cycle Time
Address Access Time
Chip Enable Access Time
Output Enable Access Time
CE Low to Output Active
OE Low to Output Active
Output Enable or Chip Disable to Output in
High Z
Output Hold from Address Change
-45
Min. Max.
45
45
45
25
0
0
0 20
0
-70
Min. Max.
70
70
70
35
0
0
0 20
-90
Min. Max.
90
90
90
45
0
0
0 30
00
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Program (Erase/Program) Cycle
Parameter
Name
tWC
tAS
tAH
tCS
tCH
tOES
tOEH
tWP
tWPH
tDS
tDH
tWHWH1
tWHWH2
tWHWH3
Parameter
Program Cycle Time
Address Setup Time
Address Hold Time
CE Setup Time
CE Hold Time
OE Setup Time
OE High Hold Time
WE Pulse Width
WE Pulse Width High
Data Setup Time
Data Hold Time
Programming Cycle
Sector Erase Cycle
Chip Erase Cycle
-45 -70 -90
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit
45 — — 70 — — 90 — — ns
0 — — 0 — — 0 — — ns
35 — — 45 — — 45 — — ns
0 — — 0 — — 0 — — ns
0 — — 0 — — 0 — — ns
0 — — 0 — — 0 — — ns
0 — — 0 — — 0 — — ns
25 — — 35 — — 45 — — ns
20 — — 35 — — 38 — — ns
20 — — 25 — — 30 — — ns
0 — — 0 — — 0 — — ns
— — 20 — — 20 — — 20 µs
— — 10 — — 10 — — 10 ms
500 — — 500 — — 500 ms
V29C51000T/V29C51000B Rev. 0.5 October 2000
5

5 Page





V29C51000B arduino
MOSEL VITELIC
Boot Block Detection
In Autoselect mode, performing a read at
address 3CXX2H or address 0CXX2H will indicate
if the Top Boot Block sector or the Bottom Boot
Block sector is locked out. If the data is 01H, the
Top/Bottom Boot Block is protected. If the data is
00H, the Top/Bottom Boot Block is unprotected.
(see Table 3.)
Device ID
In Autoselect mode, performing a read at
address XXXXH will determine whether the device
is a Top Boot Block device or a Bottom Boot Block
device. If the data is 00H, the device is a Top Boot
Block. If the data is A0H, the device is a Bottom
Boot Block device (see Table 3).
In addition, the device ID can also be read via the
command register when the device is erased or
programmed in a system without applying high
voltage to the A9 pin. When A0 is HIGH, the device
ID is presented at the outputs.
V29C51000T/V29C51000B
Manufacturer ID
In Autoselect mode, performing a read at
address. XXXX0H will determine the manufacturer
ID. 40H is the manufacturer code for Mosel Vitelic
Flash.
In addition the manufacturer ID can also be read
via the command register when the device is
erased or programmed in a system without
applying high voltage to the A9 pin. when A0 is
LOW, the manufacturer ID is presented at the
outputs.
Hardware Data Protection
VCC Sense Protection: the program operation is
inhibited when VCC is less than 2.5V.
Noise Protection: a CE or WE pulse of less than
5ns will not initiate a program cycle.
Program Inhibit Protection: holding any one of
OE LOW, CE HIGH or WE HIGH inhibits a program
cycle.
Table 3. Autoselect Decoding
Decoding Mode
Boot Block
Boot Block Protection
Top
Bottom
Device ID
Top
Bottom
Manufacture ID
NOTE:
1. X = Dont Care, VIH = HIGH, VIL = LOW.
Address
A0 A1 A2A13 A14A17 Data I/O0I/O7
VIL VIH X VIH 01H: protected
VIL VIH X VIL 00H: unprotected
VIH VIL
X
X 01H
00H
VIL VIL
X
X A0H
V29C51000T/V29C51000B Rev. 0.5 October 2000
11

11 Page







PáginasTotal 16 Páginas
PDF Descargar[ Datasheet V29C51000B.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
V29C51000B512K BIT 65/536 x 8 BIT 5 VOLT CMOS FLASH MEMORYMosel Vitelic  Corp
Mosel Vitelic Corp
V29C51000T512K BIT 65/536 x 8 BIT 5 VOLT CMOS FLASH MEMORYMosel Vitelic  Corp
Mosel Vitelic Corp

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar