|
|
PDF XE5620-ITR Data sheet ( Hoja de datos )
| Número de pieza | XE5620-ITR | |
| Descripción | 56 KBPS Surface-Mountable Integrated Sealed-Hybrid Modem | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de XE5620-ITR (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
|
No Preview Available !
XE5620
January 2003
56 KBPS Surface-Mountable Integrated Sealed-Hybrid Modem
Description
Xecom’s XE5620 provides a complete 56 KBPS
modem into an miniature, surface-mount package.
Xecom’s new HyPLCC™ package (Hybrid PLCC)
makes it possible to meet the conflicting goals of
small size, low cost and surface-mountability. The
XE5620 targets remote monitoring applications in
industrial, commercial and residential locations
As a complete modem, the XE5620 includes not only
all modem circuitry but also user transferrable FCC
Part 68 Registration and UL60950 recognition. This
allows the XE5620 to be easily integrated into your
embedded application.
Xecom’s new HyPLCC™ package infuses the XE5620
with both its small size and surface mountability. The
HyPLCC package allows complex hybrid circuits to fit
the 68-Pin PLCC footprint. The HyPLCC™ package
provides a completely sealed environment protecting
the XE5620 during assembly and board cleaning
operations. Xecom also provides a low speed model,
the XE2420, in the HyPLCC™ package.
Features
* Small Size: The HyPLCC™ measures less than 1
inch by 1 inch square and 0.290 inches thick
* Surface-mountable: The HyPLCC™ package is
equivalent to a 68-Pin PLCC device.
* Data transfer at all rates from 300 BPS to 56KBPS
using V.90, V.34bis, V.34, V.32bis, V.32, V.22bis,
V.22, V.23, V.21, Bell 212A, and Bell 103 Protocols
* Supports V.42 error correction and V.42bis Data
Compression
* Modem Control and Configuration via industry
standard AT Commands.
* Non-volatile memory stores modem configuration
and permits stored number dialing.
* Incorporates Fax send and receive capabilities
controlled by Class 1 Fax commands.
* Complete integrated DAA includes, Ring Detect,
Loop Current Holding Circuit, Hook Switch.
Metallic Surge Protection, and Solid-State DAA
* User Transferrable FCC Part 68 Registration
* UL60950 Recognition
* Low Power operation, 3.3 Volts, 300 milliwatt;
XE5620 BLOCK DIAGRAM
XECOM (1) XE5620
1 page  
XE5620 Soldering Instructions
The XE5620 is subject to damage if over-exposed to heat during solder reflow operations. Following the
soldering instructions below will ensure that the process of soldering the module to the board does not damage
the modem. The XE5620 must not be exposed to direct Infrared (IR) heating. If your process includes direct IR
heating, you must shield the XE5620 from the infrared rays.
Maximum Temperature
Maximum Time at 220O C
Maximum Time above Eutectic (180O C)
220O C
20 Seconds
90 Seconds
Maximum Preheat Dwell Time 180 Seconds
Maximum Recommended Solder Temperature Profile
220O C
180O C
150O C
--------------------------------180 sec max ---------------------
-20 sec-
max
----- 90 sec max -----
XECOM (5) XE5620
5 Page 
XE5620 AT Commands
&Kn - Flow Control
n=0 No Flow Control
n=3 RTS/CTS Flow Control *
n=4 XON/XOFF Flow Control
n=5 Transparent XON/XOFF Flow Control
&Pn - Pulse Dial Make/Break Ratio
n=0 39%/61% 10 PPS *
n=1 33%/67% 10 PPS
n=2 39%/61% 20 PPS
n=3 33%/67% 20 PPS
&Sn - Data Set Ready
n=0 Data Set Ready Forced Active *
n=1 Data Set Ready on at Start of Modem handshake
&Un - Protocol Selection
n=0 V.90 *
n=1 V.34Bis/V.34
n=2 V.32bis/V.22bis
n=3 Bell 103
n=4 V.21
n=5 V.23
&V - View Active Configuration
&Wn - Store Current Configuration
n=0 Store Active Configuration in Profile 0 *
n=1 Store Active Configuration in Profile 1
&Yn - Select Configuration to Recall
n=0 Recall Configuration Profile 0 *
n=1 Recall Configuration Profile 1
&Zn=x - Store dialing string x
%Cn - Data Compression Control
n=0 No Data Compression
n=1 Data Compression Enabled *
\Nn - Error Control Mode
n=0 Normal Mode
n=1 Direct Mode
n=2 MNP Required
n=3 MNP or Normal
n=4 Auto Error Correction V.42 without ODP or ADP
Phase Detection, MNP or Normal mode
n=5 Auto Reliable Mode *
n=6 V.42 without ODP or ADP Phase Detection required
n=7 V.42 with ODP or ADP Phase Detection required
\Vn - Protocol Result Code
n=0 No Protocol Result code added to Response *
n=1 Protocol Result code added to Response
*Hn - Automatic Retrain
n=0 Automatic Retrain Disabled
n=1 Automatically retrain on poor signal quality
*In - Select Maximum Connection Speed
n=0 1200 BPS,
n=1 2400 BPS,
28,000 with AT&U=0
n=2 4800 BPS,
29,333 with AT&U=0
n=3 7200 BPS,
30,666 with AT&U=0
n=4 9600 BPS,
32,000 with AT&U=0
n=5 12,000 BPS,
33,333 with AT&U=0
n=6 14,400 BPS,
34,666 with AT&U=0
n=7 16,800 BPS,
36,000 with AT&U=0
n=8 19,200 BPS,
37,333 with AT&U=0
n=9 21,600 BPS,
38,666 with AT&U=0
n=10 24,000 BPS,
40,000 with AT&U=0
n=11 26,400 BPS,
41,333 with AT&U=0
n=12 28,800 BPS,
42,666 with AT&U=0
n=13 31,200 BPS,
44,000 with AT&U=0
n=14 33,600 BPS *, 45,333 with AT&U=0
n=15 46,666 BPS with AT&U=0
n=16 48,000 BPS with AT&U=0
n=17 49,333 BPS with AT&U=0
n=18 50,666 BPS with AT&U=0
n=19 52,000 BPS with AT&U=0
n=20 53,333 BPS with AT&U=0
n=21 54,666 BPS with AT&U=0
n=22 56,000 BPS with AT&U=0 *
*Hn - Automatic Retrain
n=0 Automatic Retrain Disabled
n=1 Automatically retrain on poor signal quality *
XECOM (11) XE5620
11 Page | ||
| Páginas | Total 18 Páginas | |
| PDF Descargar | [ Datasheet XE5620-ITR.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| XE5620-ITR | 56 KBPS Surface-Mountable Integrated Sealed-Hybrid Modem | ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |