|
|
PDF IMSB300-1 Data sheet ( Hoja de datos )
| Número de pieza | IMSB300-1 | |
| Descripción | TCPlink Development System | |
| Fabricantes | STMicroelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IMSB300-1 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
IMS B300
TCPlink Development System
Ethernet
transceiver
Ethernet
cable
AUI cable
IMS B300
TCPLink
box
OS-Links
ST20450
Development
Board
Diagnostic
terminal
Differential sub-
system cables
(e.g. IMS CA15)
Single-ended
subsystem
cables
FEATURES
Compact desktop design, suitable for office or
computer room environments
Provides full interface to four independent net-
works over Ethernet
Uses TCP/IP protocol suite
Choice of single ended or differential link con-
nections
Independent diagnostics and test port simpli-
fies installation of software enhancements
LED activity indicators for each connection
Subsys-
tem 3
Prototyping
system
DESCRIPTION
The IMS B300 TCPlink box is a self-contained unit
providing four links and associated system ser-
vices for connection to target subsystems. The
four links are accessed over an Ethernet network
by host development computers running SGS–
THOMSON Toolsets in conjunction with the TCP/
IP protocol suite. The unit supports the develop-
ment of programs in a network environment.
Diagnostic and monitoring facilities are provided
via a serial port on the IMS B300. This may be con-
nected to an ANSI compatible video terminal to
give interactive information displays on the unit’s
operation.
INMOS is a registered trademark of SGS-THOMSON Microelectronics Limited
February 1996
42 1493 03
1/12
1 page  
IMS B300 Ethernet connection system datasheet
3.2.1 Connections to an IMS B014
The use of the IMS CA16 cable in conjunction with the connectors on a IMS B014 standard VME motherboard is illustrated
in figure 4. The jumper configuration of the motherboard is shown in figure 4. As can be seen, the single ended cable
connections from the IMS B300 are mated with a ‘breakout’ connector or ‘hedgehog’ mounted in the P4 front panel con-
nector of the IMS B014. A TRAM should be inserted in slot 0 of the IMS B014 motherboard array. Other TRAMs may
be added to the motherboard as required. The IMS B014 can be inserted in a VME rack or used in a bench-top mode
via a separate power supply.
Note that this example assumes the use of a 20Mbit/s link speed on both the IMS B300 subsystem and the IMS B014
motherboard. Also note that it is not possible to configure an IMS B014 to access the appropriate signal connections via
its back panel (P2) connector.
From IMS B300
via IMS CA16 cable
SubsystemDown
Link
FrontServicesUp (on P4)
Link 0
Link 1
Link 2
Link 3
Link 4
Link 5
Link 6
Link 7
FrontConfigUp (on P4)
Connector Link (on P4)
not used
FrontConfigDown (P5)
not used
FrontServicesDown (on P5)
Figure 4 Front panel ‘breakout’ connector on P4 of IMS B014
5/12
5 Page 
IMS B300 Ethernet connection system datasheet
Appendix A Differential Buffer circuit
11/12
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet IMSB300-1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IMSB300-1 | TCPlink Development System | STMicroelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |