|
|
PDF ILX511 Data sheet ( Hoja de datos )
| Número de pieza | ILX511 | |
| Descripción | 2048-pixel CCD Linear Image Sensor (B/W) | |
| Fabricantes | Sony Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ILX511 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
ILX511
2048-pixel CCD Linear Image Sensor (B/W)
For the availability of this product, please contact the sales office.
Description
The ILX511 is a rectangular reduction type CCD
22 pin DIP (Plastic)
linear image sensor designed for bar code POS
hand scanner and optical measuring equipment use.
A built-in timing generator and clock-drivers ensure
single 5 V power supply for easy use.
Features
• Number of effective pixels: 2048 pixels
• Pixel size:
14 µm × 200 µm
(14 µm pitch)
• Single 5 V power supply
• Ultra-high sensitivity
• Built-in timing generator and clock-drivers
• Built-in sample-and-hold circuit
• Maximum clock frequency: 2MHz
Block Diagram
Absolute Maximum Ratings
• Supply voltage
VDD
• Operating temperature
• Storage temperature
6
–10 to +60
–30 to +80
V
°C
°C
Pin Configuration (Top View)
VOUT 1
GND 2
GND 3
SHSW 4
φCLK 5
VDD 6
NC 7
NC 8
VDD 9
NC 10
φROG 11
1
2048
22 VDD
21 VDD
20 VDD
19 GND
18 VGG
17 GND
16 GND
15 VDD
14 NC
13 NC
12 GND
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
—1—
E94108-TE
1 page  
ILX511
—5—
5 Page 
ILX511
Notes on Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling, be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive
shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) Ionized air is recommended for discharge when handling CCD image sensors.
e) For the shipment of mounted substrates use cartons treated for the prevention of static charges.
2) Notes on handling CCD Cer-DIP package
The following points should be observed when handling and installing this package.
a) (1) Compressive strength: 39N/surface
(Do not apply any load more than 0.7 mm inside the outer perimeter of the glass
portion.)
(2) Shearing strength:
29N/surface
(3) Tensile strength:
29N/surface
(4) Torsional strength:
0.9Nm
Upper ceramic layer
39N
29N
0.9Nm
29N
Lower ceramic layer
Low-melting glass
(1)
(2)
(3) (4)
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the glass to crack because the upper and lower ceramic
layers are shielded by low-melting glass.
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with a soldering iron.
(3) Rapid cooling or heating.
(4) Applying a load or impact to a limited portion of the low-melting glass with a small-tipped tool such
as tweezers.
(5) Prying the upper or lower ceramic layers away at a support point of the low-melting glass.
Note that the preceding notes should also be observed when removing a component from a board
after it has already been soldered.
3) Soldering
a) Make sure the package temperature does not exceed 80 °C.
b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a grounded
30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool
sufficiently.
c) To dismount image sensors, do not use a solder suction equipment. When using an electric
desoldering tool, ground the controller. For the control system, use a zero cross type.
—11—
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet ILX511.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ILX510 | 5150-pixel CCD Linear Sensor (B/W) | Sony Corporation |
| ILX511 | 2048-pixel CCD Linear Image Sensor (B/W) | Sony Corporation |
| ILX514 | 3918-pixel CCD Linear Image Sensor (B/W) | Sony Corporation |
| ILX516K | 3648 X 3pixel CCD Linear Sensor (Color) | Sony Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |