DataSheet.es    


PDF IDT54FCT16373T Data sheet ( Hoja de datos )

Número de pieza IDT54FCT16373T
Descripción FAST CMOS 16-BIT TRANSPARENT LATCHES
Fabricantes Integrated Device Technology 
Logotipo Integrated Device Technology Logotipo



Hay una vista previa y un enlace de descarga de IDT54FCT16373T (archivo pdf) en la parte inferior de esta página.


Total 8 Páginas

No Preview Available ! IDT54FCT16373T Hoja de datos, Descripción, Manual

Integrated Device Technology, Inc.
FAST CMOS 16-BIT
TRANSPARENT
LATCHES
IDT54/74FCT16373T/AT/CT/ET
IDT54/74FCT162373T/AT/CT/ET
FEATURES:
DESCRIPTION:
• Common features:
– 0.5 MICRON CMOS Technology
– High-speed, low-power CMOS replacement for
ABT functions
Typical tSK(o) (Output Skew) < 250ps
– Low input and output leakage 1µA (max.)
– ESD > 2000V per MIL-STD-883, Method 3015;
> 200V using machine model (C = 200pF, R = 0)
– Packages include 25 mil pitch SSOP, 19.6 mil pitch
TSSOP,15.7 mil pitch TVSOP and 25 mil pitch Cerpack
– Extended commercial range of -40°C to +85°C
– VCC = 5V ±10%
• Features for FCT16373T/AT/CT/ET:
– High drive outputs (-32mA IOH, 64mA IOL)
– Power off disable outputs permit “live insertion”
– Typical VOLP (Output Ground Bounce) < 1.0V at
VCC = 5V, TA = 25°C
• Features for FCT162373T/AT/CT/ET:
– Balanced Output Drivers: ±24mA (commercial),
±16mA (military)
– Reduced system switching noise
– Typical VOLP (Output Ground Bounce) < 0.6V at
The FCT16373T/AT/CT/ET and FCT162373T/AT/CT/ET
16-bit transparent D-type latches are built using advanced
dual metal CMOS technology. These high-speed, low-power
latches are ideal for temporary storage of data. They can be
used for implementing memory address latches, I/O ports,
and bus drivers. The Output Enable and Latch Enable controls
are organized to operate each device as two 8-bit latches, or
one 16-bit latch. Flow-through organization of signal pins
simplifies layout. All inputs are designed with hysteresis for
improved noise margin.
The FCT16373T/AT/CT/ET are ideally suited for driving
high-capacitance loads and low-impedance backplanes. The
output buffers are designed with power off disable capability
to allow "live insertion" of boards when used as backplane
drivers.
The FCT162373T/AT/CT/ET have balanced output drive
with current limiting resistors. This offers low ground bounce,
minimal undershoot, and controlled output fall times– reduc-
ing the need for external series terminating resistors. The
FCT162373T/AT/CT/ET are plug-in replacements for the
FCT16373T/AT/CT/ET and ABT16373 for on-board interface
applications.
VCC = 5V,TA = 25°C
FUNCTIONAL BLOCK DIAGRAM
1OE
1LE
1D1
D
C
2OE
2LE
2D1
1O1
D
C
2O1
TO 7 OTHER CHANNELS
2543 drw 01
TO 7 OTHER CHANNELS
2543 drw 02
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
MILITARY AND COMMERCIAL TEMPERATURE RANGES
©1996 Integrated Device Technology, Inc.
5.7
AUGUST 1996
DSC-4229/9
1

1 page




IDT54FCT16373T pdf
IDT54/74FCT16373T/AT/CT/ET, 162373T/AT/CT/ET
FAST CMOS 16-BIT TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
POWER SUPPLY CHARACTERISTICS
Symbol
Parameter
Test Conditions(1)
Min. Typ.(2) Max. Unit
ICC
Quiescent Power Supply Current VCC = Max.
TTL Inputs HIGH
VIN = 3.4V(3)
— 0.5 1.5 mA
ICCD
Dynamic Power Supply
Current(4)
VCC = Max.
Outputs Open
xOE = GND
One Input Toggling
50% Duty Cycle
VIN = VCC
VIN = GND
— 60 100 µA/
MHz
IC
Total Power Supply Current(6)
VCC = Max.
VIN = VCC
Outputs Open
VIN = GND
fi =10MHz
50% Duty Cycle
xOE = GND
VIN = 3.4V
VIN = GND
xLE = VCC
One Bit Toggling
— 0.6 1.5 mA
— 0.9 2.3
VCC = Max.
VIN = VCC
— 2.4 4.5(5)
Outputs Open
VIN = GND
fi = 2.5MHz
50% Duty Cycle
xOE = GND
VIN = 3.4V
VIN = GND
— 6.4 16.5(5)
xLE = VCC
Sixteen Bits Toggling
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ICC DHNT + ICCD (fCPNCP/2 + fiNi)
ICC = Quiescent Current (ICCL, ICCH and ICCZ)
ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
NCP = Number of Clock Inputs at fCP
fi = Input Frequency
Ni = Number of Inputs at fi
2543 tbl 08
5.7 5

5 Page










PáginasTotal 8 Páginas
PDF Descargar[ Datasheet IDT54FCT16373T.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
IDT54FCT16373ATFAST CMOS 16-BIT TRANSPARENT LATCHESIntegrated Device Technology
Integrated Device Technology
IDT54FCT16373CTFAST CMOS 16-BIT TRANSPARENT LATCHESIntegrated Device Technology
Integrated Device Technology
IDT54FCT16373ETFAST CMOS 16-BIT TRANSPARENT LATCHESIntegrated Device Technology
Integrated Device Technology
IDT54FCT16373TFAST CMOS 16-BIT TRANSPARENT LATCHESIntegrated Device Technology
Integrated Device Technology

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar