DataSheet.es    


PDF IDT54FCT162841CTEB Data sheet ( Hoja de datos )

Número de pieza IDT54FCT162841CTEB
Descripción FAST CMOS 20-BIT TRANSPARENT LATCHES
Fabricantes Integrated Device Technology 
Logotipo Integrated Device Technology Logotipo



Hay una vista previa y un enlace de descarga de IDT54FCT162841CTEB (archivo pdf) en la parte inferior de esta página.


Total 9 Páginas

No Preview Available ! IDT54FCT162841CTEB Hoja de datos, Descripción, Manual

Integrated Device Technology, Inc.
FAST CMOS 20-BIT
TRANSPARENT
LATCHES
IDT54/74FCT16841AT/BT/CT/ET
IDT54/74FCT162841AT/BT/CT/ET
FEATURES:
• Common features:
– 0.5 MICRON CMOS Technology
– High-speed, low-power CMOS replacement for
ABT functions
Typical tSK(o) (Output Skew) < 250ps
– Low input and output leakage 1µA (max.)
– ESD > 2000V per MIL-STD-883, Method 3015;
> 200V using machine model (C = 200pF, R = 0)
– Packages include 25 mil pitch SSOP, 19.6 mil pitch
TSSOP, 15.7 mil pitch TVSOP and 25 mil pitch Cerpack
– Extended commercial range of -40°C to +85°C
– VCC = 5V ±10%
• Features for FCT16841AT/BT/CT/ET:
– High drive outputs (-32mA IOH, 64mA IOL)
– Power off disable outputs permit “live insertion”
– Typical VOLP (Output Ground Bounce) < 1.0V at
VCC = 5V, TA = 25°C
• Features for FCT162841AT/BT/CT/ET:
– Balanced Output Drivers: ±24mA (commercial),
±16mA (military)
– Reduced system switching noise
– Typical VOLP (Output Ground Bounce) < 0.6V at
VCC = 5V,TA = 25°C
DESCRIPTION:
The FCT16841AT/BT/CT/ET and FCT162841AT/BT/CT/
ET 20-bit transparent D-type latches are built using advanced
dual metal CMOS technology. These high-speed, low-power
latches are ideal for temporary storage of data. They can be
used for implementing memory address latches, I/O ports,
and bus drivers. The Output Enable and Latch Enable controls
are organized to operate each device as two 10-bit latches or
one 20-bit latch. Flow-through organization of signal pins
simplifies layout. All inputs are designed with hysteresis for
improved noise margin.
The FCT16841AT/BT/CT/ET are ideally suited for driving
high-capacitance loads and low-impedance backplanes. The
output buffers are designed with power off disable capability
to allow "live insertion" of boards when used as backplane
drivers.
The FCT162841AT/BT/CT/ET have balanced output drive
with current limiting resistors. This offers low ground bounce,
minimal undershoot, and controlled output fall times–reducing
the need for external series terminating resistors. The
FCT162841AT/BT/CT/ET are plug-in replacements for the
FCT16841AT/BT/CT/ET and ABT16841 for on-board inter-
face applications.
FUNCTIONAL BLOCK DIAGRAM
1OE
1LE
1D1
D
C
2OE
2LE
2D1
1Q1
D
C
2Q1
TO 9 OTHER CHANNELS
2556 drw 01
TO 9 OTHER CHANNELS
2556 drw 02
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
MILITARY AND COMMERCIAL TEMPERATURE RANGES
©1996 Integrated Device Technology, Inc.
5.18
JULY 1996
DSC-2556/7
1

1 page




IDT54FCT162841CTEB pdf
IDT54/74FCT16841AT/BT/CT/ET, 162841AT/BT/CT/ET
FAST CMOS 20-BIT TRANSPARENT LATCHES
MILITARY AND COMMERCIAL TEMPERATURE RANGES
POWER SUPPLY CHARACTERISTICS
Symbol
ICC
ICCD
IC
Parameter
Quiescent Power Supply Current
TTL Inputs HIGH
Dynamic Power Supply
Current(4)
Total Power Supply Current(6)
Test Conditions(1)
VCC = Max.
VIN = 3.4V(3)
VCC = Max.
Outputs Open
xOE = GND
One Input Toggling
50% Duty Cycle
VIN = VCC
VIN = GND
VCC = Max.
Outputs Open
fi =10MHz
50% Duty Cycle
xOE = GND
xLE = VCC
One Bit Toggling
VIN = VCC
VIN = GND
VIN = 3.4V
VIN = GND
VCC = Max.
Outputs Open
fi = 2.5MHz
50% Duty Cycle
xOE = GND
xLE = VCC
Twenty Bits Toggling
VIN = VCC
VIN = GND
VIN = 3.4V
VIN = GND
Min. Typ.(2) Max. Unit
— 0.5 1.5 mA
— 60 100 µA/
MHz
— 0.6 1.5 mA
— 0.9 2.3
— 3.0 5.5(5)
— 8.0 20.5(5)
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ICC DHNT + ICCD (fCPNCP/2 + fiNi)
ICC = Quiescent Current (ICCL, ICCH and ICCZ)
ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
NCP = Number of Clock Inputs at fCP
fi = Input Frequency
Ni = Number of Inputs at fi
2556 tbl 08
5.18 5

5 Page










PáginasTotal 9 Páginas
PDF Descargar[ Datasheet IDT54FCT162841CTEB.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
IDT54FCT162841CTEFAST CMOS 20-BIT TRANSPARENT LATCHESIntegrated Device Technology
Integrated Device Technology
IDT54FCT162841CTEBFAST CMOS 20-BIT TRANSPARENT LATCHESIntegrated Device Technology
Integrated Device Technology

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar