DataSheet.es    


PDF BA6803S Data sheet ( Hoja de datos )

Número de pieza BA6803S
Descripción Fluorescent display tube level meter driver/ 16-point x 2 channel/ VU scale/ bar display
Fabricantes ROHM Semiconductor 
Logotipo ROHM Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de BA6803S (archivo pdf) en la parte inferior de esta página.


Total 7 Páginas

No Preview Available ! BA6803S Hoja de datos, Descripción, Manual

Audio ICs
Fluorescent display tube level meter
driver, 16-point 2 channel, VU scale,
bar display
BA6803S
The BA6803S is a two-channel, 16-point fluorescent display tube driver for VU-scale bar-level meters. It uses a dynamic-
drive system and has both AC and DC inputs.
The AC input mode has a peak hold circuit. The IC features a power-on mute, and the output block can directly drive
fluorescent display tubes, so few external components are required.
The grid output duty cycle is 1 / 8.
FApplications
Level meters for all types of AV equipment
FFeatures
1) Uses dynamic-drive system to display two 16-point
channels. 30-pin SDIP package.
2) AC and DC inputs provided. Switching function al-
lows two-mode display.
3) Upper 12 points have peak hold function in AC mode
(two seconds typ.).
4) Power-on mute function.
5) Dynamic-drive system reduces the power dissipa-
tion of the fluorescent display tube power supply.
6) Square root compression amplifier built in.
FAbsolute maximum ratings (Ta = 25_C)
811

1 page




BA6803S pdf
Audio ICs
FCircuit operation
(1) Input block
The AC input pins are pins 1 and 3, and the DC input pins
are pins 6 and 7. Pin 8 is used to switch between the AC
and DC inputs. When the input to pin 8 is “H”, AC input
is selected (pins 1 and 3).
Therefore, by using pin 8 to switch between the AC and
DC modes, the IC can do two jobs, using one fluorescent
tube. For example, pins 1 and 3 can be used for audio sig-
nal input, and pins 6 and 7 can be used as the input for
the signal meter output from a tuner (DC). The AC input
impedance of pins 1 and 3 is a low 250(typ.), so con-
nect potentiometers (VR1 and VR2) in series with the in-
puts to adjust the sensitivity and ch1 and ch2 balance.
(2) Peak hold circuit
The BA6803S features a peak hold circuit that temporari-
ly holds peak signal levels in AC input mode.
The peak hold function can be used with the upper 12
points (5 to 16). The peak hold time depends on the oscil-
lator frequency. It is 2 sec. (typ.) for an oscillator frequen-
cy of 2kHz.
DC mode does not have a peak hold function.
(3) Grid output
The pin 10 and 11 grid outputs are open-collector NPN
transistors. The logic is active low (the fluorescent tube
lights when the output is “L”), so connect two PNP tran-
sistors Q1 and Q2 as shown in the application example
circuit to drive the fluorescent tubes (see Fig. 3).
BA6803S
(4) Segment output block
Pins 12 to 28 are the segment outputs. The output cir-
cuits are open-collector PNP transistors. When grid 1 is
“L”, the ch1 level is output (pin 1 or 6 input level), and
when grid 2 is “L”, the ch2 level is output (pin 3 or 7 input
level). Refer to Fig. 4.
(5) Grid and segment output timing chart. The grid and
segment output timing is shown in Fig. 5.
(6) Attack and release times
The response characteristic for AC input signals is set by
resistor R1 and capacitor C3 for ch1 and resistor R2 and
capacitor C4 for ch2 (pins 2 and 4). When R1 = 47kand
C3 = 22µF, the attack time is about 4ms, and the release
time is about 1sec. (same for ch2).
Attack time : Time for the voltage on pins 2 and 4
to rise from 1V to 2.5V when the in-
put goes from no input to 2.6Vrms,
then back to no input.
Release time : Time for the voltage on pins 2 and 4
to fall from 2.5V to 1V when the input
goes from 2.6Vrms to no input.
(7) Oscillator frequency
The resistor R26 and capacitor C5 connected to pin 30 de-
termine the oscillator frequency. The oscillator frequency
(fosc) and grid output period (T) are related as follows:
T (ms) = 16 / fosc (kHz)
815

5 Page










PáginasTotal 7 Páginas
PDF Descargar[ Datasheet BA6803S.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
BA6803Fluorescent display tube level meter driver/ 16-point x 2 channel/ VU scale/ bar displayROHM Semiconductor
ROHM Semiconductor
BA6803SFluorescent display tube level meter driver/ 16-point x 2 channel/ VU scale/ bar displayROHM Semiconductor
ROHM Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar