DataSheet.es    


PDF BA3842 Data sheet ( Hoja de datos )

Número de pieza BA3842
Descripción Preset equalizer sound control (P.S.C) IC
Fabricantes ROHM Semiconductor 
Logotipo ROHM Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de BA3842 (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! BA3842 Hoja de datos, Descripción, Manual

Audio ICs
Preset equalizer sound control
(P.S.C) IC
BA3842F
The BA3842F is a preset graphic equalizer IC with dynamic bass boost which is designed for audio equipment.
FApplications
Mini-component stereos
Micro-component stereos
Radio cassette recorders with CD
FFeatures
1) Includes preset equalizer function with five equalizer
positions and a flat mode setting.
2) Built-in dynamic bass boost with gain settings from 0
to 20dB in steps of 5dB.
3) Low distortion and low noise.
4) Built-in dynamic bass boost and interlocked ALC
(Auto Level Control).
FAbsolute maximum ratings (Ta = 25_C)
FRecommended operating conditions
563

1 page




BA3842 pdf
Audio ICs
BA3842F
567

5 Page





BA3842 arduino
Audio ICs
BA3842F
(6) Filter for preset equalizer
(1) Low band
The low cutoff frequency fc of each mode is given by the
following equation :
fc = 1 / 2πCR = 1 / (2π C 15.6k)
When C = 0.22µF,
fc 46 (Hz)
The fc value can be changed to make slight changes in
the boost and cutoff gain of each mode.
(2) High band
The high cutoff frequencies fc of each mode are given by
the following equation :
fc = 1 / 2πCR
When C = 2200pF,
ROCK : R = 8.0k
fc 9.0 (kHz)
JAZZ : R = 10.7k
fc 6.8 (kHz)
CLASSIC : R = 14.9kfc 4.8 (kHz)
BGM. POP : R = 17.4kfc 4.2 (kHz)
The fc values can be changed to make slight changes in
the boost and cutoff gain of each mode.
Note:
If a high or low fc value is changed, the gains of all modes
will change. The gain cannot be changed for only one
mode.
(7) ALC
The band of ALC detection can be changed with the val-
ue of C4. It must be adjusted appropriately for the dynam-
ic bass boost fO. In the example application circuit C4 =
0.1µF, thus fc = 1 / 2πC4 (R5 / / R6 / / R7)
160 (Hz)
The detection wave is dually rectified. In the example ap-
plication circuit, it is 1.3Vrms, but if the resistors R8 and R9
are connected as shown below, it will lower the ALC level.
Adjust the ALC level as needed. The detection band at
this time is :
fc = 1 / 2πC4 (R5 / / R6 / / R7 / / R8 / / / R9)
(8) Attack time and release time
Adjust the attack and release times with the resistors and
capacitors connected to the ALCC pin. The attack time
is determined by R10 (1k) and C5, and the release time
is determined by R11 and C5. If the value set for C5 is below
4.7µF, the ALC level may become unstable.
573

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet BA3842.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
BA3840KVPreset graphic equalizer for headphone stereosROHM Semiconductor
ROHM Semiconductor
BA3842Preset equalizer sound control (P.S.C) ICROHM Semiconductor
ROHM Semiconductor
BA3842FPreset equalizer sound control (P.S.C) ICROHM Semiconductor
ROHM Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar